Zanussi ZCM ID manual Connecting to GAS, Connection to the Electricity Supply

Page 49

4. CONNECTING TO GAS

50

100

This appliance is designed to be installed with an

 

 

appliance flexible connection only. Supply piping should

 

 

not be less that R³/8. Connection is made to the Rc ½ (½"

 

 

B.S.P.) female threaded entry pipe located just below the

 

 

hotplate level on the rear left hand side of the appliance.

 

 

NOTE: ONLY LIQUID SEALANTS TO BE USED WHEN

 

 

INLET GAS PIPE IS FITTED TO SHUT OFF VALVE

 

 

I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Check for

 

 

gas soundness after connecting to the gas supply.

 

 

The gas bayonet connector must be fitted in the shaded

850

 

area indicated in Fig.3. Take into account that it must be

 

 

 

possible to pull the appliance forward sufficiently. The

 

 

hose must not get caught on the stability bracket.

 

 

IMPORTANT: FLEXIBLE TUBING USED MUST

 

 

COMPLY WITH BS. 669 CURRENT EDITION.

 

 

 

250

 

All dimensions in mm

5. CONNECTION TO THE ELECTRICITY SUPPLY

WARNING: THIS APPLIANCE MUST BE EARTHED.

DO NOT EARTH THIS APPLIANCE TO THE GAS

SUPPLY PIPING.

This appliance must be connected to a 230V A.C. 50Hz supply. It is supplied with 2 metres of 15 amp 3 core cable incorporating a moulded 13 amp plug , fitted with a 13 amp fuse, which can be plugged directly into the nearest suitable socket. If this is not long enough, the supply cable can be either:-

(i)Replaced totally by a longer cable at least 1.5mm² nominal cross sectional area (30/0.25mm).

(ii)Extended by using a B.E.A.B. approved 3-way sealed flex connector with integral flex clamps.

IF THE MOULDED PLUG IS CUT FROM THE CABLE

FOR ANY REASON, IT MUST BE DESTROYED OR

DISPOSED OF SAFELY, AS THE PROTRUDING

WIRES WILL BE AN ELECTRIC SHOCK HAZARD.

Fig.3

450 700

Fig.4

If any other type of plug is used it should incorporate a 13 amp fuse in either the plug or adapter or at the distribution board.

If the cable has to be threaded through small apertures in cabinets etc., it may be disconnected from the appliance, then re-connected to as shown in Fig.4.

DO NOT EXTEND THE CABLE USING PLASTIC OR CERAMIC CONNECTION TERMINAL BLOCKS AND/OR INSULATION TAPE.

ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND THE ELECTRICAL SUPPLY SHALL COMPLY WITH I.E.E. WIRING REGULATIONS.

49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Page Introduction For your safetyContents Hotplate Lighting the cookerSecond oven Grill/second ovenMain fan oven To turn off any burnerTo use the oven To turn off the ovenGrill Grill control has two heat settingsHeat control Cooking positionsPreheating General Plate warmingPositioning food on the grid Grill shelfGrill pan is supplied with a removable handle Grill pan and handleBurner sizes HotplateFor your safety Helpful hints Fan oven Cooking temperaturesMinutes Oven shelves Batch bakingBaking trays and dishes Roasting Gas top ovenSuch as Yorkshire puddings, soufflés and yeast mixtures Circulate around the foodCondensation Oven Cooking Chart Main fan oven Casseroles Beef/lamb Food Cooking ApproximateChicken FishRoast Potatoes VegetablesStuffed Marrow Stuffed TomatoesRoasting chart Oven cooking chart Second oven Minutes for each ½kg 1lb Duck and duckling Shelf on Mins. per ½kg 1lbIndividual 20 30 mins Cakes Christmas cake Shelf Hours 20 30 mins Pastries Plate tart shortcrust 25 35 minsBaked custard 50 60 mins 45 60 minsUses of defrost feature Defrost featureSelecting defrost Hints and tips Things to noteTo set the time of day Electronic timerTo use the minute minder Turn the selector knob back to manualAutomatic control Setting the controls for automatic useShowing Selector knob to Correct time? Either directionTo cook? How long will Turn the selector knob to Food takeDisplay Hints and tips for automatic cooking Care and cleaning For your safety Grill and oven furniture When replacing hotplate burner partsCrown to body Do not try to force the crown on to the body Main fan oven To carry out a cleaning cycle Remove the oven shelves Turn Main oven cleaning cycleClean. Some Staining 220C for 1 2 hours or until OvenGeneral Top oven cleaning cycleRemove the oven shelf Set the oven to mark 5 for at least 30 minutesYou can remove the glass from the oven door if you need to Cleaning between the outer and inner door glassInstalling the cooker Cleaning The Door GlassLocation Make sure that a stability bracket is fittedPositioning Cooker dimensionsCurtains behind the cooker Height to hotplate 898mm 920mmConnecting to the electricity supply General information For your safetyMoving your cooker Replacing the oven light bulb Check What is wrong and why?Oven. See pages 5 7 0 5 9 2 9 9 2 Service and spare partsCustomer Care Department Standard guarantee conditions Guarantee ConditionsDimensions Technical DataProvision for Ventilation Important Safety RequirementsLocation of Appliance Location of Storage Board Levelling the Appliance Parts RequiredFitting the Stability Bracket Connection to the Electricity Supply Connecting to GASChecking the Grill Pressure TestingChecking the Hotplate Checking LID SHUT-OFF DeviceChecking the Main Oven Checking the Main Oven ControlsAutomatic Operation Checking the Main Oven LightT E S T E S ZCM I D Page Electrolux Household Appliances Limited

ZCM ID specifications

The Zanussi ZCM ID is a standout appliance designed for the modern kitchen, known for its user-friendly features, impressive technologies, and sleek design. As a versatile addition to any cooking space, this induction cooktop combines efficiency with style, making it a popular choice among both amateur cooks and culinary enthusiasts.

One of the key features of the Zanussi ZCM ID is its induction cooking technology. Unlike traditional gas or electric cooktops, induction cooking uses electromagnetic energy to heat pots and pans directly, ensuring rapid and precise temperature control. This not only speeds up the cooking process but also enhances safety, as the cooktop surface remains cooler to the touch, significantly reducing the risk of burns.

The cooktop boasts an intuitive interface, making it easy for users to navigate through its various settings. It features touch controls that allow for quick adjustments, ensuring a seamless cooking experience. The timer function is another highlight, enabling users to set specific cooking times for different dishes to achieve perfect results every time.

Another distinguishing characteristic of the Zanussi ZCM ID is its sleek design. The smooth glass-ceramic surface not only looks elegant but is also easy to clean. Spills and splatters can be wiped away effortlessly, saving time in kitchen maintenance. The modern aesthetic of the cooktop complements a variety of kitchen styles, from contemporary to traditional.

The appliance also features multiple cooking zones, each with varying sizes and power levels to accommodate different cookware. Whether using a small saucepan or a large frying pan, the Zanussi ZCM ID caters to diverse cooking needs. Furthermore, the boost function allows for extra power when boiling or searing, providing that additional burst of heat when needed.

Safety is a top priority with the Zanussi ZCM ID. The appliance is equipped with safety lock features to prevent accidental operation, especially in households with children. Additionally, the automatic shut-off function ensures that the cooktop turns off if it is left unused for a specific period, offering peace of mind to users.

In summary, the Zanussi ZCM ID is an innovative induction cooktop that offers a blend of advanced cooking technologies, stylish design, and exceptional safety features. With its user-friendly controls, easy maintenance, and efficient cooking capabilities, it stands out as a must-have appliance for anyone looking to elevate their culinary experience.
Top Page Image Contents