Sherwood R-963 manual Power button and then save the code, Repeat the above steps

Page 15

Enter the 3 digit setup code aiming the

7 remote control at the REMOTE SENSOR on the component.

OSD

OFF

PAGE

MAIN

FAV

VOL

 

CH

 

 

 

For "001" :

0

0

1

1

2

3

 

 

 

 

4

5

6

 

 

 

 

7

8

9

For "102" :

1

0

2

MI

M2

M3

 

0

 

 

 

 

 

 

RNC-500

 

 

 

 

 

Your component will be turned off when the right code is entered.

Continue to enter the corresponding codes until your component turns off.

To resume the MAIN menu mode, press the

9 MAIN button twice briefly.

8

Confirm that it is the right code by pressing

the POWER button and then save the code.

OSD

POWER

OFF

 

The code is saved and the Pre-PROgramming mode is resumed.

When you do not want to save the code, select the EXIT on the LCD screen or press the MAIN button.

Operate the component using the

10 corresponding function buttons.

ENGLISH

OSD

OFF

MAIN

PAGE

VOL

1

4

7

MAIN

FAV

 

CH

2 3

56

89

0

If any of the buttons fails to operate as they should, start from the step again to enter the next setup code. Notes:

If the Manufacturer/Brand for your component is not listed in “Set-Up Code Table” in the operating manual of this remote control, please use the “ 2 Auto Scan Method” on page 13 in the operating manual of this

MI M2 M3

The selected device

RNC-500

 

Each time the MAIN button is pressed, the previous mode is resumed.

remote control.

Although each setup code is designed to work with many different modes, certain codes may not work with some models.( Also, certain codes may only operate some of the functions available on a given model.)

11 Repeat the above steps

to

for each of your other components.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 963 Introduction Unpacking and InstallationRead this Before Operating Your Unit Room 2 Remote Controls Should this happen, memorize them again System ConnectionsAudio IN/ OUT connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting Speakers Dynamic Range Button Front Panel ControlsUniversal Remote Controls Digi Link System Remote ControlsThis remote control unit has 3 operating modes as follows Function Table of the Numbered Buttons 5V matching the polarity Loading BatteriesRemove the cover Load four alkaline batteries AAA sizeButtons simultaneously for 3 seconds Entering a Setup CodeRepeat the above steps Power button and then save the codeCode is saved and the Pre-PROgramming mode is resumed Operate the component using Corresponding function buttonsFunctions Main Additional Information on Remote Command CodesMatching the polarity Room 2 Remote ControlsBefore operation OperationsSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 5 is selectedAdjusting the tone bass and treble Select the tone mode as desiredPress it again to cancel, then CINEMA-EQ OFF Surround modes Surround SoundHall 1/2 Use this mode to enjoy video game sourcesFront left and right speakers and center speaker Speaker placementEnjoying Surround Sound Surr Adjusting each channel level with test tone Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorConnected, Digital is flickering. There Digital Audio Recording with MD RecorderEach time this button is pressed, the corresponding Input is selected as followsCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Room 2 source Room 2 Source PlaybackUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP /DOWN buttonsWhen selecting the Power AMP Assign When selecting the Function SelectSetting the Power AMP Assign When selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance Corresponding LFE level mode When selecting the LFE Level ControlSetting the Function Select When selecting the Input SetupMoved to the corresponding Digital D E O S E L E C T When selecting the Tone Control Off To turn off the current status display When selecting the OSD ModeWhen the DC Trigger mode is set to On When selecting the DC TriggerWhen selecting the Listening Mode Moved to the corresponding mode Setting the Surround SetupWhen selecting the Source Direct When selecting the Cinema EQWhen selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim Be adjusted within the range of -15~+15 dBEach time these buttons are pressed, the channel level can When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen selecting the Function Select for Room Press the Cursor UP /DOWN Then press the Enter buttonButtons to select the Function Select for Room 2 source Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications963

R-963 specifications

The Sherwood R-963 is a standout receiver in the competitive audio equipment landscape, renowned for its blend of traditional craftsmanship and cutting-edge technology. This model exemplifies Sherwood's commitment to high-fidelity sound, making it a popular choice among audiophiles and casual listeners alike.

One of the defining features of the R-963 is its robust power output, delivering 100 watts per channel across a wide frequency range. This ensures that listeners experience rich sound dynamics, whether enjoying quiet acoustic tracks or the thunderous crescendos of orchestral material. The receiver is designed to accommodate a variety of speaker configurations, supporting both 2-channel and multi-channel setups, which allows it to cater to personal preferences and home theater requirements.

The R-963 is equipped with an array of connectivity options, reflecting the demands of modern audio environments. It includes multiple HDMI inputs, allowing seamless connections to a range of devices, from Blu-ray players to gaming consoles. Additionally, the receiver supports 4K passthrough, ensuring high-definition content is transmitted without loss of quality. For those who enjoy streaming, the built-in Bluetooth capability allows wireless music playback from smartphones and tablets, enhancing convenience and flexibility.

Another notable technology in the R-963 is its advanced audio processing features. The receiver utilizes digital signal processing (DSP) to optimize sound quality, enabling users to select various audio modes that enhance music and movie watching experiences. Surround sound capabilities are also integrated, offering immersive audio that replicates a theater-like atmosphere at home.

User-friendly controls and a clear display make the R-963 accessible for all users. The ergonomic remote control allows effortless navigation between functions, settings, and sources, making the operation enjoyable. Additionally, compatibility with multi-room audio systems means that users can enjoy their favorite tunes in various rooms simultaneously.

In summary, the Sherwood R-963 receiver combines powerful performance with versatile connectivity and modern technologies. Its robust build quality, user-friendly interface, and exceptional audio capabilities make it an excellent choice for anyone looking to elevate their listening experience, whether it be through music playback or movie soundtracks.
Top Page Image Contents