Sherwood R-963 manual Digital Audio Recording with MD Recorder, Input is selected as follows

Page 31

Start recording on the component hooked

3 up to the VIDEO 1.

Start play on the components hooked up to

4 the VIDEO 2 and the CD respectively.

The audio signal from the CD and the video signal from the VIDEO 2 component will be dubbed and you can enjoy them on the TV set and from the speakers.

Note : Be sure to observe the order of the above steps and .

ENGLISH

DIGITAL AUDIO RECORDING WITH MD RECORDER

Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to “ CONNECTING AUDIO COMPONENTS” and “CONNECTING DIGITAL INs and OUT” on page 5 and 7 and the operating instructions of the MD recorder or CD recorder.

Notes:

Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc. In most DVDs as well as some CDs, etc., digital recording may not be available depending on the signal format.

There are some restrictions on recording digital signals. When making digital recordings, refer to the operating instructions of your digital recording equipment to know what restrictions are imposed.

1

Select a desired input of CD, TAPE

2

For digital recording, select the desired

MONITOR and VIDEO 1~VIDEO 5 as a

digital input as the recording signal input.

recording source.

 

 

 

 

 

 

 

 

 

DIGITAL/ANALOG

OSD

POWER

 

 

 

 

OFF

 

 

 

OSD

POWER

 

 

 

 

 

INPUT SELECTOR

OFF

 

 

 

or

 

AUDIO

VIDEO TAPE MON.

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

Each time this button is pressed, the corresponding

 

 

 

 

input is selected as follows:

 

 

 

 

 

DIGITAL

ANALOG

 

 

 

 

 

Note : When the selected digital input is not

 

 

 

 

 

connected, “DIGITAL” is flickering. There

 

 

 

 

 

will be no recording as well as no sound.

3

Start recording on the component

4

Start play on the desired input.

connected to OPTICAL DIGITAL OUT.

 

 

 

31

Image 31
Contents 963 Introduction Unpacking and InstallationRead this Before Operating Your Unit Room 2 Remote Controls Should this happen, memorize them again System ConnectionsAudio IN/ OUT connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting Speakers Dynamic Range Button Front Panel ControlsDigi Link System Remote Controls Universal Remote ControlsThis remote control unit has 3 operating modes as follows Function Table of the Numbered Buttons 5V matching the polarity Loading BatteriesRemove the cover Load four alkaline batteries AAA sizeButtons simultaneously for 3 seconds Entering a Setup CodeRepeat the above steps Power button and then save the codeCode is saved and the Pre-PROgramming mode is resumed Operate the component using Corresponding function buttonsFunctions Main Additional Information on Remote Command CodesMatching the polarity Room 2 Remote ControlsBefore operation OperationsSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 5 is selectedAdjusting the tone bass and treble Select the tone mode as desiredPress it again to cancel, then CINEMA-EQ OFF Surround modes Surround SoundHall 1/2 Use this mode to enjoy video game sourcesFront left and right speakers and center speaker Speaker placementEnjoying Surround Sound Surr Adjusting each channel level with test tone Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorConnected, Digital is flickering. There Digital Audio Recording with MD RecorderEach time this button is pressed, the corresponding Input is selected as followsCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Room 2 source Room 2 Source PlaybackOSD Menu Settings Using the OSDCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP /DOWN buttonsWhen selecting the Power AMP Assign When selecting the Function SelectSetting the Power AMP Assign When selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance Corresponding LFE level mode When selecting the LFE Level ControlWhen selecting the Input Setup Setting the Function SelectMoved to the corresponding Digital D E O S E L E C T When selecting the Tone Control Off To turn off the current status display When selecting the OSD ModeWhen the DC Trigger mode is set to On When selecting the DC TriggerWhen selecting the Listening Mode Moved to the corresponding mode Setting the Surround SetupWhen selecting the Source Direct When selecting the Cinema EQWhen selecting the surround mode When selecting the Decoding ModeBe adjusted within the range of -15~+15 dB Setting the CH Level TrimEach time these buttons are pressed, the channel level can When selecting the Volume Mode Setting the ROOM2 Feed SetupPress the Cursor UP /DOWN Then press the Enter button When selecting the Function Select for RoomButtons to select the Function Select for Room 2 source Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications963

R-963 specifications

The Sherwood R-963 is a standout receiver in the competitive audio equipment landscape, renowned for its blend of traditional craftsmanship and cutting-edge technology. This model exemplifies Sherwood's commitment to high-fidelity sound, making it a popular choice among audiophiles and casual listeners alike.

One of the defining features of the R-963 is its robust power output, delivering 100 watts per channel across a wide frequency range. This ensures that listeners experience rich sound dynamics, whether enjoying quiet acoustic tracks or the thunderous crescendos of orchestral material. The receiver is designed to accommodate a variety of speaker configurations, supporting both 2-channel and multi-channel setups, which allows it to cater to personal preferences and home theater requirements.

The R-963 is equipped with an array of connectivity options, reflecting the demands of modern audio environments. It includes multiple HDMI inputs, allowing seamless connections to a range of devices, from Blu-ray players to gaming consoles. Additionally, the receiver supports 4K passthrough, ensuring high-definition content is transmitted without loss of quality. For those who enjoy streaming, the built-in Bluetooth capability allows wireless music playback from smartphones and tablets, enhancing convenience and flexibility.

Another notable technology in the R-963 is its advanced audio processing features. The receiver utilizes digital signal processing (DSP) to optimize sound quality, enabling users to select various audio modes that enhance music and movie watching experiences. Surround sound capabilities are also integrated, offering immersive audio that replicates a theater-like atmosphere at home.

User-friendly controls and a clear display make the R-963 accessible for all users. The ergonomic remote control allows effortless navigation between functions, settings, and sources, making the operation enjoyable. Additionally, compatibility with multi-room audio systems means that users can enjoy their favorite tunes in various rooms simultaneously.

In summary, the Sherwood R-963 receiver combines powerful performance with versatile connectivity and modern technologies. Its robust build quality, user-friendly interface, and exceptional audio capabilities make it an excellent choice for anyone looking to elevate their listening experience, whether it be through music playback or movie soundtracks.