Sherwood R-963 manual When selecting the Decoding Mode, When selecting the surround mode

Page 48

ENGLISH

When selecting the DECODING MODE

Depending on the input digital signal format, you can select the desired decoding mode. Auto : Select this for automatic detection of a digital input signal format.

The input digital signal format (DTS, Dolby Digital, MPEG or PCM(2 channel stereo), etc.) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround modes.

Dolby Digital : Select this for Dolby Digital signal processing. The decoding process is preformed only when Dolby Digital signals are input.

DTS : Select this for DTS signal processing. The decoding process is performed only when DTS signals are input.

MPEG : Select this for MPEG signal processing. The decoding process is performed only when MPEG signals are input.

PCM : Select this for PCM signal processing. The decoding process is performed only when PCM signals are input.

Notes :

Surround sound effect will not work properly if the signal passes through a graphic equalizer.

Please refer to your equalizer operating instructions for guidance on switching off(or defeating) the equalizer.

Only when the digital input is selected as signal input for the input sources except PHONO, TUNER and AUX, the decoding mode can be selected.

Noise may be generated at the beginning of playback and while searching during DTS playback in the auto mode. In this case, try playing in the DTS mode.

When selecting the surround mode

Depending on the input signal format and the selected decoding mode, you can select the desired surround mode as follows: * When Dolby Digital signals are input in the auto or Dolby Digital mode, the following modes can be selected.

DOLBY DIGITAL ( DOLBY PRO LOGIC II MOVIE DOLBY PRO LOGIC II MUSIC DOLBY PRO LOGIC) DOLBY VIRTUAL

Only when Dolby Digital 2.0 channel signals are input, the surround modes in ( ) can be selected, too.

* When PCM(2 channel stereo) signals are input in the auto or PCM mode, the following modes can be selected.

DOLBY PRO LOGIC II MOVIE

 

DOLBY PRO LOGIC II MUSIC

DOLBY PRO LOGIC DOLBY VIRTUAL DTS NEO MOVIE DTS NEO MUSIC

 

 

 

MATRIX GAME ARENA

2

ARENA 1 CLUB 2 CLUB 1

CHURCH STADIUM HALL 2 HALL 1 MOVIE THEATER

 

 

 

 

When the analog input is selected as signal input and analog stereo signals are input, you can select the desired of these above surround modes, too.

However, when DTS or MPEG signals are input in the following decoding modes, the corresponding surround mode will be automatically selected:

*When DTS signals are input in the auto or DTS mode, the corresponding DTS mode will be selected.

*When MPEG signals are input in the auto or MPEG mode, MPEG mode will be selected.

Notes :

When the selected decoding mode is not matched to the input signal format, the indicator of the signal being input is flickering, meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format.

When the 7.1 CH DIRECT is selected as an input source, the surround mode cannot be selected.

To play some multi-channel program sources in the Extra Surround 6.1/7.1 mode,

When the digital signals from the following program sources only are input in the available decoding mode, press the EXTRA SURROUND 6.1/7.1 button on the front panel or the 7.1 CH SURROUND button on the remote control, then the corresponding surround mode will be selected.

*Dolby Digital 5.1-channel sources(including THX Surround EX created using the Dolby Digital Surround EX technology) : EXTRA SURROUND mode,

*DTS 5.1-channel sources : DTS ES MATRIX mode.

Press the EXTRA SURROUND 6.1/7.1 button or the 7.1 CH SURROUND button again to cancel the 6.1(or 7.1) surround mode.

According to whether the surround back speaker is set to “1 CH” or “2 CH”, the 6.1 or 7.1 mode is selected. However, when the surround back speaker is set to “None”, the Extra Surround 6.1/7.1 mode cannot be activated.

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents 963 Unpacking and Installation IntroductionRead this Before Operating Your Unit Room 2 Remote Controls System Connections Should this happen, memorize them againAudio IN/ OUT connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting Speakers Front Panel Controls Dynamic Range ButtonUniversal Remote Controls Digi Link System Remote ControlsThis remote control unit has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverLoad four alkaline batteries AAA size 5V matching the polarityEntering a Setup Code Buttons simultaneously for 3 secondsPower button and then save the code Code is saved and the Pre-PROgramming mode is resumedOperate the component using Corresponding function buttons Repeat the above stepsAdditional Information on Remote Command Codes Functions MainRoom 2 Remote Controls Matching the polarityOperations Before operationWhen CD, Tape MON or Video 1~ Video 5 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredPress it again to cancel, then CINEMA-EQ OFF Surround Sound Surround modesUse this mode to enjoy video game sources Hall 1/2Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Surr Adjusting each channel level Adjusting each channel level with test toneDownmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Each time this button is pressed, the correspondingInput is selected as follows Connected, Digital is flickering. ThereOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Room 2 Source Playback Room 2 sourceUsing the OSD OSD Menu SettingsCurrent Status Display Select the desired menu using the Cursor UP /DOWN buttons When selecting the Power AMP AssignWhen selecting the Function Select When selecting the Surround SetupSetting the Power AMP Assign Setting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control Corresponding LFE level modeSetting the Function Select When selecting the Input SetupMoved to the corresponding Digital D E O S E L E C T When selecting the Tone Control When selecting the OSD Mode Off To turn off the current status displayWhen selecting the DC Trigger When the DC Trigger mode is set to OnWhen selecting the Listening Mode Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ Moved to the corresponding modeWhen selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Be adjusted within the range of -15~+15 dBEach time these buttons are pressed, the channel level can Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room Press the Cursor UP /DOWN Then press the Enter buttonButtons to select the Function Select for Room 2 source Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section963

R-963 specifications

The Sherwood R-963 is a standout receiver in the competitive audio equipment landscape, renowned for its blend of traditional craftsmanship and cutting-edge technology. This model exemplifies Sherwood's commitment to high-fidelity sound, making it a popular choice among audiophiles and casual listeners alike.

One of the defining features of the R-963 is its robust power output, delivering 100 watts per channel across a wide frequency range. This ensures that listeners experience rich sound dynamics, whether enjoying quiet acoustic tracks or the thunderous crescendos of orchestral material. The receiver is designed to accommodate a variety of speaker configurations, supporting both 2-channel and multi-channel setups, which allows it to cater to personal preferences and home theater requirements.

The R-963 is equipped with an array of connectivity options, reflecting the demands of modern audio environments. It includes multiple HDMI inputs, allowing seamless connections to a range of devices, from Blu-ray players to gaming consoles. Additionally, the receiver supports 4K passthrough, ensuring high-definition content is transmitted without loss of quality. For those who enjoy streaming, the built-in Bluetooth capability allows wireless music playback from smartphones and tablets, enhancing convenience and flexibility.

Another notable technology in the R-963 is its advanced audio processing features. The receiver utilizes digital signal processing (DSP) to optimize sound quality, enabling users to select various audio modes that enhance music and movie watching experiences. Surround sound capabilities are also integrated, offering immersive audio that replicates a theater-like atmosphere at home.

User-friendly controls and a clear display make the R-963 accessible for all users. The ergonomic remote control allows effortless navigation between functions, settings, and sources, making the operation enjoyable. Additionally, compatibility with multi-room audio systems means that users can enjoy their favorite tunes in various rooms simultaneously.

In summary, the Sherwood R-963 receiver combines powerful performance with versatile connectivity and modern technologies. Its robust build quality, user-friendly interface, and exceptional audio capabilities make it an excellent choice for anyone looking to elevate their listening experience, whether it be through music playback or movie soundtracks.
Top Page Image Contents