Sherwood R-963 manual Surr

Page 25

Continued

When playing some multi-channel program sources in the Extra Surround 6.1/7.1 mode.

OSD

OFF

EXTRA SURR.

PAGE

MAIN

FAV

6.1/7.1

or

VOLCH

 

 

7.1

SURR

1 2 3

4 5 6

7 8 9

0

MI M2 M3

RNC-500

When the digital signals from the following program sources only are input in the available decoding mode, if these buttons are pressed, the corresponding surround mode will be selected.

Dolby Digital 5.1-channel sources(including THX Surround EX created using the Dolby Digital Surround EX technology) : EXTRA SURROUND mode,

DTS 5.1-channel sources : DTS ES MATRIX mode.

Press the EXTRA SURROUND 6.1/7.1 button on the front panel or the 7.1 CH SURROUND button on the remote control again to cancel the 6.1(or 7.1) surround mode.

According to whether the surround back speaker is set to “1CH” or “2CH”, the 6.1 or 7.1 mode is selected. However, when the surround back speaker is set to “None”, the Extra Surround 6.1/7.1 mode cannot be activated.

When canceling the surround mode for normal stereo operation.

OSD

OFF

STEREO

 

PAGE

MAIN

FAV

 

VOL

 

CH

or

 

 

 

STEREO

1

2

3

 

4

5

6

7 8 9

0

MI M2 M3

RNC-500

Then the stereo mode is selected.

To cancel the stereo mode, select the desired surround mode with using the MULTI CONTROL knob or the DSP MODE button, etc.

ENGLISH

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 963 Introduction Unpacking and InstallationRead this Before Operating Your Unit Room 2 Remote Controls Should this happen, memorize them again System ConnectionsAudio IN/ OUT connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting Speakers Dynamic Range Button Front Panel ControlsDigi Link System Remote Controls Universal Remote ControlsThis remote control unit has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesLoad four alkaline batteries AAA size 5V matching the polarityButtons simultaneously for 3 seconds Entering a Setup CodeCode is saved and the Pre-PROgramming mode is resumed Power button and then save the codeOperate the component using Corresponding function buttons Repeat the above stepsFunctions Main Additional Information on Remote Command CodesMatching the polarity Room 2 Remote ControlsBefore operation OperationsAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 5 is selectedSelect the tone mode as desired Select the digital or the analog input as DesiredPress it again to cancel, then CINEMA-EQ OFF Surround modes Surround SoundHall 1/2 Use this mode to enjoy video game sourcesFront left and right speakers and center speaker Speaker placementEnjoying Surround Sound Surr Adjusting each channel level with test tone Adjusting each channel levelDownmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoEach time this button is pressed, the corresponding Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereAdjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Room 2 source Room 2 Source PlaybackOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Select the desired menu using the Cursor UP /DOWN buttonsWhen selecting the Function Select When selecting the Surround SetupSetting the Power AMP Assign When selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance Corresponding LFE level mode When selecting the LFE Level ControlWhen selecting the Input Setup Setting the Function SelectMoved to the corresponding Digital D E O S E L E C T When selecting the Tone Control Off To turn off the current status display When selecting the OSD ModeWhen the DC Trigger mode is set to On When selecting the DC TriggerWhen selecting the Listening Mode When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ Moved to the corresponding modeWhen selecting the surround mode When selecting the Decoding ModeBe adjusted within the range of -15~+15 dB Setting the CH Level TrimEach time these buttons are pressed, the channel level can When selecting the Volume Mode Setting the ROOM2 Feed SetupPress the Cursor UP /DOWN Then press the Enter button When selecting the Function Select for RoomButtons to select the Function Select for Room 2 source Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications963

R-963 specifications

The Sherwood R-963 is a standout receiver in the competitive audio equipment landscape, renowned for its blend of traditional craftsmanship and cutting-edge technology. This model exemplifies Sherwood's commitment to high-fidelity sound, making it a popular choice among audiophiles and casual listeners alike.

One of the defining features of the R-963 is its robust power output, delivering 100 watts per channel across a wide frequency range. This ensures that listeners experience rich sound dynamics, whether enjoying quiet acoustic tracks or the thunderous crescendos of orchestral material. The receiver is designed to accommodate a variety of speaker configurations, supporting both 2-channel and multi-channel setups, which allows it to cater to personal preferences and home theater requirements.

The R-963 is equipped with an array of connectivity options, reflecting the demands of modern audio environments. It includes multiple HDMI inputs, allowing seamless connections to a range of devices, from Blu-ray players to gaming consoles. Additionally, the receiver supports 4K passthrough, ensuring high-definition content is transmitted without loss of quality. For those who enjoy streaming, the built-in Bluetooth capability allows wireless music playback from smartphones and tablets, enhancing convenience and flexibility.

Another notable technology in the R-963 is its advanced audio processing features. The receiver utilizes digital signal processing (DSP) to optimize sound quality, enabling users to select various audio modes that enhance music and movie watching experiences. Surround sound capabilities are also integrated, offering immersive audio that replicates a theater-like atmosphere at home.

User-friendly controls and a clear display make the R-963 accessible for all users. The ergonomic remote control allows effortless navigation between functions, settings, and sources, making the operation enjoyable. Additionally, compatibility with multi-room audio systems means that users can enjoy their favorite tunes in various rooms simultaneously.

In summary, the Sherwood R-963 receiver combines powerful performance with versatile connectivity and modern technologies. Its robust build quality, user-friendly interface, and exceptional audio capabilities make it an excellent choice for anyone looking to elevate their listening experience, whether it be through music playback or movie soundtracks.
Top Page Image Contents