Sherwood R-963 manual Setting the Function Select, When selecting the Input Setup

Page 41

SETTING THE FUNCTION SELECT

											To adjust the input source as desired.
F U N C T I O N S E L E C T											To adjust the input source as desired.
F U N C T I O N S E L E C T
I N P U T S E T U P											To adjust the tone as desired.
											To adjust the tone as desired.


T O N E C O N T R O L											To select the desired OSD mode.
T O N E C O N T R O L
O S D M O D E
O S D M O D E
D C T R I G G E R
L I S T E N I N G M O D E											To select the desired input source that uses
R E T U R N : B a c k	E N T E R : S e l e c t										To select the desired input source that uses
R E T U R N : B a c k	E N T E R : S e l e c t										the DC trigger function.
											To select the desired digital re-mastering mode.
											To select the desired digital re-mastering mode.

Note:

When the source direct function is selected, the TONE CONTROL cannot be selected.

When selecting the INPUT SETUP

Press the CURSOR UP( )/DOWN( ) buttons to select the INPUT SETUP, then press the ENTER button.

1

ENGLISH

OSD

OFF

PAGE	MAIN	FAV
VOL		CH

1 2 3

4 5 6

7 8 9

0

I N P U T S E T U P

D I G I T A L I N S E T U P

V I D E O S E L E C T

R E T U R N : B a c k

E N T E R : S e l e c t

To match the connected DIGITAL INs to the desired input sources respectively.

To select a video input source.

MI M2 M3

RNC-500

When selecting the DIGITAL IN SETUP

You can match the connected DIGITAL INs to the desired of CD, TAPE MONITOR and VIDEO 1~5. (For details, refer to “CONNECTING DIGITAL INs and OUT” on page 7.)

Press the CURSOR UP( )/DOWN( ) buttons to select the DIGITAL IN SETUP, then press the ENTER

2 button.

OSD

OFF

PAGE	MAIN	FAV
VOL		CH

1 2 3

4 5 6

7 8 9

0

D I G I T A L I N S E T U P

C D	:	COAX1
T A P E M O N	:	OPT4
V I D E O 1	:	OPT1
V I D E O 2	:	OPT2
V I D E O 3	:	OPT3
V I D E O 4	:	COAX2
V I D E O 5	:	OPT5
R E T U R N : B a c k		, : S e l e c t

MI M2 M3

RNC-500

“OPT 5” means the OPTICAL IN on the front panel.

Press the CURSOR UP( )/DOWN( ) buttons to select the desired input source.

3	OSD
	OFF

PAGE	MAIN	FAV	Each time these buttons are pressed, “ ” and “ ” are
VOL		CH	Each time these buttons are pressed, “ ” and “ ” are
			moved to the corresponding DIGITAL IN.

1 2 3

4 5 6

7 8 9

0

MI M2 M3

RNC-500

41

Image 41

Contents 963 Introduction Unpacking and InstallationRead this Before Operating Your Unit Room 2 Remote Controls Should this happen, memorize them again System ConnectionsAudio IN/ OUT connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting Speakers Dynamic Range Button Front Panel ControlsThis remote control unit has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Remove the cover Loading BatteriesLoad four alkaline batteries AAA size 5V matching the polarityButtons simultaneously for 3 seconds Entering a Setup CodeCode is saved and the Pre-PROgramming mode is resumed Power button and then save the codeOperate the component using Corresponding function buttons Repeat the above stepsFunctions Main Additional Information on Remote Command CodesMatching the polarity Room 2 Remote ControlsBefore operation OperationsAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 5 is selectedSelect the tone mode as desired Select the digital or the analog input as DesiredPress it again to cancel, then CINEMA-EQ OFF Surround modes Surround SoundHall 1/2 Use this mode to enjoy video game sourcesFront left and right speakers and center speaker Speaker placementEnjoying Surround Sound Surr Adjusting each channel level with test tone Adjusting each channel levelDownmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoEach time this button is pressed, the corresponding Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereAdjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Room 2 source Room 2 Source PlaybackCurrent Status Display Using the OSDOSD Menu Settings When selecting the Power AMP Assign Select the desired menu using the Cursor UP /DOWN buttonsWhen selecting the Function Select When selecting the Surround SetupSetting the Power AMP Assign When selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance Corresponding LFE level mode When selecting the LFE Level ControlMoved to the corresponding Digital Setting the Function SelectWhen selecting the Input Setup D E O S E L E C T When selecting the Tone Control Off To turn off the current status display When selecting the OSD ModeWhen the DC Trigger mode is set to On When selecting the DC TriggerWhen selecting the Listening Mode When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ Moved to the corresponding modeWhen selecting the surround mode When selecting the Decoding ModeEach time these buttons are pressed, the channel level can Setting the CH Level TrimBe adjusted within the range of -15~+15 dB When selecting the Volume Mode Setting the ROOM2 Feed SetupButtons to select the Function Select for Room 2 source When selecting the Function Select for RoomPress the Cursor UP /DOWN Then press the Enter button Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications963