Sherwood RD-7502 manual Switched AC Outlets, AC Input Cord

Page 10

ENGLISH

10. SWITCHED AC OUTLETS

•These outlets are switched on(power-on mode) and off(standby mode) according to power control as follows(Maximum total capacity is 120 W (1 A)).

Standby mode - Switched AC outlet off Power-on mode - Switched AC outlet on

11. AC INPUT CORD

•Plug this cord into a wall AC outlet.

Speaker placement

Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows :

Front left and right speakers and center speaker

•Place the front speakers with their front surfaces as flush with TV or monitor screen as possible.

•Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers.

•Place each speaker so that sound is aimed at the location of the listener’s ears when at the main listening position.

Surround left and right speakers

•Place the surround speakers approximately 1 meter (40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind.

Surround back left and right speakers

•Place the surround back speakers at the back facing the front at a narrower distance than front speakers.

•When using a single surround back speaker, place it at the rear center facing the front at a slightly higher position (0 to 20 cm) than the surround speakers.

•We recommend installing the surround back speaker(s) at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp.

1.	TV or screen	7.	Surround right speaker
2.	Front left speaker	8.	Surround back left speaker
3.	Subwoofer	9.	Surround back right speaker
4.	Center speaker	10.		Surround center speaker
5.	Front right speaker	11.		Listening position
6.	Surround left speaker

Subwoofer

•The subwoofer reproduces powerful deep bass sounds. Place a subwoofer anywhere in the front as desired.

Notes :

•When using a conventional TV, to avoid interference with the TV picture, use only magnetically shielded front left and right and center speakers.

•To obtain the best surround effects, the speakers except the subwoofer should be full range speakers.

10

Image 10

Contents RD-7502 Safety Instructions Read this Before Operating Your Unit For Your SafetyIntroduction FCC InformationContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Connecting XM only for North America Connecting Subwoofer PRE OUTConnecting DIGI-LINK Connecting SpeakersSwitched AC Outlets AC Input CordFluorescent Display Front Panel ControlsRemote Sensor AUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Display buttonRemote Control Operation Range Loading BatteriesOperations When selecting the External in as desiredBefore operation When CD, AUX, Video 1~2 is selected as an input source Reproduced through the headphonesTone mode is displayed for several seconds Adjusting the tone bass and trebleEnter the tone mode Sources are input or the External in is selected canSurround Sound Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Pro LogicSelect the desired surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modeSP When using 2 front and center speakers Pressed, the parameter mode changes as followsControl can be set it 8 steps from 0 to 7 default value Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersDolby Headphone Parameters Adjusting each channel level with test toneEnter the test tone mode SB orAdjusting the current channel level BL BRRecalling the memorized channel levels Memorizing the adjusted channel levels1 of REF 1 indication flickers for several seconds Auto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Manual presettingMemory Backup Function Scanning preset stations in sequenceSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaSelect XM Category search Channel searchDirect search For 27 2Signal strength display mode Presetting channelsPreset search Error message and statusRecording with Tape Dubbing the audio and video signals separately onto VideoRecording Dubbing from video components onto VideoStart recording on the component connected to Digital Audio Recording with MD RecorderOptical Digital OUT Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Displaying the operation statusNavigating through the setup menu System SetupDown System Setup menu flowSetup menu flow is as follows Input SPK SETCH Level Paramtr ExitWhen selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the TonePress the Cursor Left /RIGHT When selecting the Digital Setting the InputInput When selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsWhen performing the auto setup When the auto setup has been completedWhen setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationSpeaker types When setting the distance When selecting the Speaker DistanceWhen selecting the desired unit About the speaker sizeButtons to select the desired speaker When selecting the Speaker CrossoverAbout the crossover frequency 40 ~ 200 Hz in 10 Hz intervalsOFF When turning off the room EQ mode On When turning it onSetting the CH Level CH LevelUP /DOWN RightSetting the Sound Parameter Lower compression Higher compressionWhen selecting the Pano Panorama mode When selecting the Dolby Plii MusicWhen selecting the C. Width Center width control Each time the Cursor UP / Down buttons are pressed When selecting the Dolby HeadphoneDH 1 Dolby Headphone 1, DH 2 or DH 3 is selected Reference mode When selecting the Dolby Virtual SpeakerWhen selecting the REF Dolby Virtual Speaker When selecting the Wide Dolby Virtual SpeakerTroubleshooting Guide Problem Possible Cause RemedySpecifications RD-7502