Sherwood RD-7502 manual System Connections, Connecting Antennas

Page 5

System Connections

Do not plug the AC input cord into the wall AC outlet until all connections are completed.

Be sure to observe the color coding when connecting audio, video and speaker cords.

Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.

ENGLISH

ANTENNA

FM 75

GND

AM

LOOP

MONITOR OUT

XM

EXTERNAL IN

 

COAX 2

 

 

SUR.BACK

TAPE OUT

COAX 1

CENTER

 

SUBWOOFER

VIDEO 1 OUT

OPT 2

 

 

SURROUND

TAPE

OPT 1

 

 

FRONT

VIDEO 2

OPT OUT

 

 

CD

VIDEO 1

 

R

L

R

L

DIGITAL

 

 

AUDIO

 

DIGI-LINK

PRE OUT

SUBWOOFER

MONITOR OUT

VIDEO

VIDEO 1 OUT

VIDEO 1

VIDEO 2

 

 

PR/CR

PB/CB

Y

MONITOR OUT

 

PR/CR

PB/CB

Y

VIDEO 2

 

 

 

 

 

 

VIDEO 1

 

PR/CR

PB/CB

Y

 

S-VIDEO

COMPONENT VIDEO

 

Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are

trademarks of Dolby Laboratories.

 

 

 

Manufactured under license from Digital

MODEL NO. RD-7502

 

 

 

 

Theater Systems, Inc. U.S. Pat. No's.

SN.

5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 and other

AUDIO/ VIDEO RECEIVER

U.S. and world-wide patents issued and pending.

 

 

"DTS", "DTS-ES", "DTS 96/24" and "Neo:6" are trademarks of

MADE IN CHINA

 

Digital Theater Systems, Inc. Copyright 1996, 2003-2005 Digital

 

DESIGNED IN USA

 

Theater Systems, Inc. All Rights Reserved.

 

 

 

 

 

 

SPEAKERS

 

 

 

 

FRONT

 

SURROUND

CENTER

SURROUND BACK

AC OUTLET

 

 

(6

)

 

(6

)

(6

)

(6

)

 

R

 

L

R

L

 

 

R

L

120V~60Hz

 

 

 

 

 

 

 

 

 

SWITCHED

 

 

 

 

 

 

 

 

 

TOTAL 120W(1A) MAX.

AC INPUT 120V~60Hz 3.8A

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference,and (2)This device must accept any interference received, including interference that may cause undesired opera- tion.

1. CONNECTING ANTENNAS

Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations.

Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception.

If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna.

A 75outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one.

5

Image 5
Contents RD-7502 Safety Instructions Introduction For Your SafetyRead this Before Operating Your Unit FCC InformationContents System Connections Connecting AntennasHDMIHigh Definition Multimedia Interface connection Connecting Video ComponentsConnecting Audio Components Digital input default settings Connecting External INSConnecting Digital INS and OUT Connecting DIGI-LINK Connecting Subwoofer PRE OUTConnecting XM only for North America Connecting SpeakersAC Input Cord Switched AC OutletsRemote Sensor Front Panel ControlsFluorescent Display Video 3 in Jacks Setup MIC JackAUX in Jack Display button Remote ControlsLoading Batteries Remote Control Operation RangeBefore operation When selecting the External in as desiredOperations Reproduced through the headphones When CD, AUX, Video 1~2 is selected as an input sourceEnter the tone mode Adjusting the tone bass and trebleTone mode is displayed for several seconds Sources are input or the External in is selected canSurround Sound Dolby Pro Logic II surround Dolby Pro Logic IIx surroundDolby Virtual Speaker Dolby Pro LogicEnjoying Surround Sound Select the desired surround mode2CH downmix mode To cancel the surround mode for stereo operationControl can be set it 8 steps from 0 to 7 default value Pressed, the parameter mode changes as followsSP When using 2 front and center speakers Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersEnter the test tone mode Adjusting each channel level with test toneDolby Headphone Parameters SB orBL BR Adjusting the current channel level1 of REF 1 indication flickers for several seconds Memorizing the adjusted channel levelsRecalling the memorized channel levels Manual tuning Auto tuningAuto presetting Listening to Radio BroadcastsMemory Backup Function Manual presettingTuning to preset stations Scanning preset stations in sequenceSelect XM XM Satellite Radio only for North AmericaSigning up for XM Satellite Radio Direct search Channel searchCategory search For 27 2Preset search Presetting channelsSignal strength display mode Error message and statusRecording Dubbing the audio and video signals separately onto VideoRecording with Tape Dubbing from video components onto VideoOptical Digital OUT Digital Audio Recording with MD RecorderStart recording on the component connected to Adjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Displaying the operation statusDown System SetupNavigating through the setup menu Setup menu flow is as follows Setup menu flowSystem Input SPK SETExit CH Level ParamtrWhen selecting the Subwoofer mode Setting the SystemWhen selecting the AMP Assign Press the Cursor Left /RIGHT When selecting the ToneWhen selecting the Cinema EQ Input Setting the InputWhen selecting the Digital When selecting the Auto Surround When selecting the Video ModeWhen selecting the Remaster When selecting the AV SyncWhen selecting the Auto Setup Setting the Speaker SetupPreparations About the first listening positionWhen the auto setup has been completed When performing the auto setupSpeaker types When selecting the Speaker ConfigurationWhen setting the speaker size by performing the auto setup When selecting the desired unit When selecting the Speaker DistanceWhen setting the distance About the speaker sizeAbout the crossover frequency When selecting the Speaker CrossoverButtons to select the desired speaker 40 ~ 200 Hz in 10 Hz intervalsOn When turning it on OFF When turning off the room EQ modeCH Level Setting the CH LevelRight UP /DOWNLower compression Higher compression Setting the Sound ParameterWhen selecting the C. Width Center width control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode DH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the Dolby HeadphoneEach time the Cursor UP / Down buttons are pressed When selecting the REF Dolby Virtual Speaker When selecting the Dolby Virtual SpeakerReference mode When selecting the Wide Dolby Virtual SpeakerProblem Possible Cause Remedy Troubleshooting GuideSpecifications RD-7502