Sherwood RD-7502 manual When selecting the Dolby Headphone

Page 52

ENGLISH

Continued

When selecting the DOLBY HEADPHONE

•You can select the desired listening mode for each Dolby Headphone mode.

Note: The listening mode setting is valid only when playing analog stereo, PCM 2 channel or Dolby Digital 2 channel source in a Dolby Headphone mode.

1. Press the CURSOR UP( )/DOWN( ) buttons to select the “DOLBY HP”, then press the ENTER button.

7	8	9
7
		MUTE
P.SCAN	0		VOLUME
	0
D/A MODE		CH.LEVEL
DISPLAY			SETUP
SEL	ENTER		SEL
T						ENTER
E
S
T
ST	SEARCH MODE		OU	N	D
ER	EO		OU
	EO		RR
			SU
	SOUND		EXT.IN
TONE PARAMETER			EXT.IN
TAPE	VIDEO 1	VIDEO 2	VIDEO 3
FM/AM/XM	CD	AUX

2. Press the CURSOR UP( )/DOWN( ) buttons to select the desired Dolby Headphone mode.

8	9
7
	MUTE
P.SCAN	VOLUME
0
D/A MODE	CH.LEVEL
DISPLAY	SETUP

T	ENTER		SEL		• Each time the CURSOR UP( ) / DOWN( ) buttons are pressed,
SEL	ENTER		SEL		“DH 1” (Dolby Headphone 1), “DH 2” or “DH 3” is selected.
STER	SEARCH MODE		OU N	D	“DH 1” (Dolby Headphone 1), “DH 2” or “DH 3” is selected.
E
S
T
	EO		RR
			SU
	SOUND		EXT.IN
TONE PARAMETER			EXT.IN
TAPE	VIDEO 1	VIDEO 2	VIDEO 3
FM/AM/XM	CD	AUX
3. Press the CURSOR LEFT(					)/ RIGHT( ) buttons to select the desired listening mode.

7

		MUTE
P.SCAN	0		VOLUME
	0
D/A MODE		CH.LEVEL
DISPLAY			SETUP
SEL	ENTER		SEL
T
E
S
T
ST	SEARCH MODE		OU	N	D
ER	EO		OU
	EO		RR
			SU
	SOUND		EXT.IN
TONE PARAMETER			EXT.IN
TAPE	VIDEO 1	VIDEO 2	VIDEO 3
FM/AM/XM	CD	AUX

MOVIE : This provides the surround effect suitable for movie sources.

MSC 1 (MUSIC 1) : This provides the surround effect suitable for music sources.

MSC 2 (MUSIC 2) : This provides less surround effect compared to MUSIC 1 mode.

4. Repeat the above steps 2 and 3 to select the desired listening modes for other Dolby Headphone modes.

52

Image 52

Contents RD-7502 Safety Instructions For Your Safety IntroductionRead this Before Operating Your Unit FCC InformationContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Connecting Subwoofer PRE OUT Connecting DIGI-LINKConnecting XM only for North America Connecting SpeakersSwitched AC Outlets AC Input CordFluorescent Display Front Panel ControlsRemote Sensor AUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Display buttonRemote Control Operation Range Loading BatteriesOperations When selecting the External in as desiredBefore operation When CD, AUX, Video 1~2 is selected as an input source Reproduced through the headphonesAdjusting the tone bass and treble Enter the tone modeTone mode is displayed for several seconds Sources are input or the External in is selected canSurround Sound Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby Pro LogicSelect the desired surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modePressed, the parameter mode changes as follows Control can be set it 8 steps from 0 to 7 default valueSP When using 2 front and center speakers Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersAdjusting each channel level with test tone Enter the test tone modeDolby Headphone Parameters SB orAdjusting the current channel level BL BRRecalling the memorized channel levels Memorizing the adjusted channel levels1 of REF 1 indication flickers for several seconds Auto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionTuning to preset stations Scanning preset stations in sequenceSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaSelect XM Channel search Direct searchCategory search For 27 2Presetting channels Preset searchSignal strength display mode Error message and statusDubbing the audio and video signals separately onto Video RecordingRecording with Tape Dubbing from video components onto VideoStart recording on the component connected to Digital Audio Recording with MD RecorderOptical Digital OUT Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the operation statusNavigating through the setup menu System SetupDown Setup menu flow Setup menu flow is as followsSystem Input SPK SETCH Level Paramtr ExitWhen selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the TonePress the Cursor Left /RIGHT When selecting the Digital Setting the InputInput When selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsWhen performing the auto setup When the auto setup has been completedWhen setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationSpeaker types When selecting the Speaker Distance When selecting the desired unitWhen setting the distance About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyButtons to select the desired speaker 40 ~ 200 Hz in 10 Hz intervalsOFF When turning off the room EQ mode On When turning it onSetting the CH Level CH LevelUP /DOWN RightSetting the Sound Parameter Lower compression Higher compressionWhen selecting the Pano Panorama mode When selecting the Dolby Plii MusicWhen selecting the C. Width Center width control Each time the Cursor UP / Down buttons are pressed When selecting the Dolby HeadphoneDH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual SpeakerReference mode When selecting the Wide Dolby Virtual SpeakerTroubleshooting Guide Problem Possible Cause RemedySpecifications RD-7502