Sherwood RD-7502 manual Remote Control Operation Range, Loading Batteries

Page 14

REMOTE CONTROL OPERATION RANGE

ENGLISH

AUDIO/VIDEO RECEIVER RD-7502

POWER ON			STANDBY
	2	3	SLEEP
1	2	3
1
	5	6	DIMMER
4	5	6
4
7	8	9
7
		MUTE
P.SCAN	0		VOLUME
	0
D/A MODE		CH.LEVEL
DISPLAY			SETUP
SEL	ENTER		SEL
T
E
ST
STE	SEARCH		U N	D
REO
			S
	SOUND		EXT.IN
TONE PARAMETER			EXT.IN
TAPE	VIDEO 1	VIDEO 2	VIDEO 3
FM/AM/XM	CD	AUX

REMOTE CONTROL RC-110

LOADING BATTERIES

1. Remove the cover.

•Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.

2. Load two batteries("AAA" size, 1.5V) matching the

polarity.

•Remove the batteries when they are not used for a long time.

•Do not use the rechargeable batteries(Ni-Cd type).

Image 14

Contents RD-7502 Safety Instructions Read this Before Operating Your Unit For Your SafetyIntroduction FCC InformationContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Digital input default settings Connecting External INSConnecting Digital INS and OUT Connecting XM only for North America Connecting Subwoofer PRE OUTConnecting DIGI-LINK Connecting SpeakersSwitched AC Outlets AC Input CordRemote Sensor Front Panel ControlsFluorescent Display Video 3 in Jacks Setup MIC JackAUX in Jack Remote Controls Display buttonRemote Control Operation Range Loading BatteriesBefore operation When selecting the External in as desiredOperations When CD, AUX, Video 1~2 is selected as an input source Reproduced through the headphonesTone mode is displayed for several seconds Adjusting the tone bass and trebleEnter the tone mode Sources are input or the External in is selected canSurround Sound Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Pro LogicSelect the desired surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modeSP When using 2 front and center speakers Pressed, the parameter mode changes as followsControl can be set it 8 steps from 0 to 7 default value Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersDolby Headphone Parameters Adjusting each channel level with test toneEnter the test tone mode SB orAdjusting the current channel level BL BR1 of REF 1 indication flickers for several seconds Memorizing the adjusted channel levelsRecalling the memorized channel levels Auto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Manual presettingMemory Backup Function Scanning preset stations in sequenceSelect XM XM Satellite Radio only for North AmericaSigning up for XM Satellite Radio Category search Channel searchDirect search For 27 2Signal strength display mode Presetting channelsPreset search Error message and statusRecording with Tape Dubbing the audio and video signals separately onto VideoRecording Dubbing from video components onto VideoOptical Digital OUT Digital Audio Recording with MD RecorderStart recording on the component connected to Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Displaying the operation statusDown System SetupNavigating through the setup menu System Setup menu flowSetup menu flow is as follows Input SPK SETCH Level Paramtr ExitWhen selecting the Subwoofer mode Setting the SystemWhen selecting the AMP Assign Press the Cursor Left /RIGHT When selecting the ToneWhen selecting the Cinema EQ Input Setting the InputWhen selecting the Digital When selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsWhen performing the auto setup When the auto setup has been completedSpeaker types When selecting the Speaker ConfigurationWhen setting the speaker size by performing the auto setup When setting the distance When selecting the Speaker DistanceWhen selecting the desired unit About the speaker sizeButtons to select the desired speaker When selecting the Speaker CrossoverAbout the crossover frequency 40 ~ 200 Hz in 10 Hz intervalsOFF When turning off the room EQ mode On When turning it onSetting the CH Level CH LevelUP /DOWN RightSetting the Sound Parameter Lower compression Higher compressionWhen selecting the C. Width Center width control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode DH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the Dolby HeadphoneEach time the Cursor UP / Down buttons are pressed Reference mode When selecting the Dolby Virtual SpeakerWhen selecting the REF Dolby Virtual Speaker When selecting the Wide Dolby Virtual SpeakerTroubleshooting Guide Problem Possible Cause RemedySpecifications RD-7502