Sherwood RD-7502 manual When selecting the Video Mode, When selecting the Auto Surround

Page 40

ENGLISH

Continued

When selecting the VIDEO MODE

• You can select the video input signal to be output from the MONITOR OUTs other than the HDMI MONITOR OUT.

“AT” (AUTO) : When there are multiple video input signals, the video input signals are detected and the video input signal to be output from the MONITOR OUTs is selected automatically in the following order : component video, S- video, composite video.

“CPS” (COMPOSITE) : The signal that is input into the (COMPOSITE) VIDEO jack is always played. The composite video input signal is up-converted and output from the S-VIDEO and COMPONENT MONITOR OUT jacks.

“SVD” (S-VIDEO) : The signal that is input into the S-VIDEO jack is always played. The S-video input signal is converted and output from the (COMPOSITE) VIDEO and COMPONENT MONITOR OUT jacks.

“CPN” (COMPONENT) : The signals that are input into the COMPONENT jacks are always played.

Because video conversion is not performed, no video signals are output from the MONITOR OUT jacks when there are no video signals that are input into the COMPONENT jacks.

• For details, refer to "Relationship between the video input signal and the video output signal" on page 7.

When selecting the AUTO SURROUND

• Depending on how to select a surround mode, you can select the auto surround mode or the manual surround mode.

OFF: You can select the desired of different surround modes selectable for the signal being input with using

(Manual surround mode) the MULTI CONTROL knob or the SURROUND MODE UP/DOWN ( >/< ) buttons. (For details, refer to

 

"When selecting the manual surround mode with pressing the SURROUND MODE button on the front

 

panel" on page 20.)

ON

: The optimum surround mode will be automatically selected depending on the signal format being input.

(Auto surround mode)

 

Notes :

•When the SPEAKER button is set to off, the auto surround mode is invalid.

•Even when the auto surround mode is selected and the same type of digital signal format is being input, the optimum surround mode may vary depending on whether the speaker type is set to "N” (None) or not.

•When the auto surround mode is selected and the PCM (2 channel) digital signal or the analog stereo signal is being input, only the stereo mode will be selected.

•When the auto surround mode is selected, the surround modes other than the optimum surround mode cannot be selected.

When selecting the REMASTER

•The remastering processes the input digital signal and converts its digital sampling frequency to twice the current frequency (88.2/96 kHz) for a more detailed sound reproduction.

OFF : To turn off the remastering function.

ON : To process the input digital signal and to convert its sampling frequency to 88.2/96 kHz for a more detailed sound reproduction.

Notes:

•The remastering function have no effect on the input digital signal from the 88.2/96 kHz source or higher as well as the digital signal that is output from the OPTICAL DIGITAL OUT of this receiver.

•When playing an analog input source, the remastering function cannot be activated.

When selecting the AV SYNC

•There may be a slight time delay between the video and audio signals in case that some video playback equipments may process the video signals later than the audio signals due to signal processing procedure, etc.. Should this happen, you can adjust the time delay of audio signals to synchronize the sound with the picture.

•The time delay can be adjusted within the range of 0 ~ 200 msec.

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents RD-7502 Safety Instructions For Your Safety IntroductionRead this Before Operating Your Unit FCC InformationContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Connecting Subwoofer PRE OUT Connecting DIGI-LINKConnecting XM only for North America Connecting SpeakersSwitched AC Outlets AC Input CordFluorescent Display Front Panel ControlsRemote Sensor AUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Display buttonRemote Control Operation Range Loading BatteriesOperations When selecting the External in as desiredBefore operation When CD, AUX, Video 1~2 is selected as an input source Reproduced through the headphonesAdjusting the tone bass and treble Enter the tone modeTone mode is displayed for several seconds Sources are input or the External in is selected canSurround Sound Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby Pro LogicSelect the desired surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modePressed, the parameter mode changes as follows Control can be set it 8 steps from 0 to 7 default valueSP When using 2 front and center speakers Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersAdjusting each channel level with test tone Enter the test tone modeDolby Headphone Parameters SB orAdjusting the current channel level BL BRRecalling the memorized channel levels Memorizing the adjusted channel levels1 of REF 1 indication flickers for several seconds Auto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionTuning to preset stations Scanning preset stations in sequenceSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaSelect XM Channel search Direct searchCategory search For 27 2Presetting channels Preset searchSignal strength display mode Error message and statusDubbing the audio and video signals separately onto Video RecordingRecording with Tape Dubbing from video components onto VideoStart recording on the component connected to Digital Audio Recording with MD RecorderOptical Digital OUT Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the operation statusNavigating through the setup menu System SetupDown Setup menu flow Setup menu flow is as followsSystem Input SPK SETCH Level Paramtr ExitWhen selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the TonePress the Cursor Left /RIGHT When selecting the Digital Setting the InputInput When selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsWhen performing the auto setup When the auto setup has been completedWhen setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationSpeaker types When selecting the Speaker Distance When selecting the desired unitWhen setting the distance About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyButtons to select the desired speaker 40 ~ 200 Hz in 10 Hz intervalsOFF When turning off the room EQ mode On When turning it onSetting the CH Level CH LevelUP /DOWN RightSetting the Sound Parameter Lower compression Higher compressionWhen selecting the Pano Panorama mode When selecting the Dolby Plii MusicWhen selecting the C. Width Center width control Each time the Cursor UP / Down buttons are pressed When selecting the Dolby HeadphoneDH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual SpeakerReference mode When selecting the Wide Dolby Virtual SpeakerTroubleshooting Guide Problem Possible Cause RemedySpecifications RD-7502
Top Page Image Contents