Sherwood RD-7502 manual Connecting Subwoofer PRE OUT, Connecting DIGI-LINK, Connecting Speakers

Page 9

6. CONNECTING SUBWOOFER PRE OUT

•To emphasize the deep bass sounds, connect a powered subwoofer.

ENGLISH

7. CONNECTING DIGI-LINK

•Connect this jack to the DIGI LINK jack of the external Sherwood component that uses the DIGI LINK II or III remote control system.

Note :

•The DIGI LINK operation may not work on some Sherwood components.

8. CONNECTING XM (only for North America)

•Connect the XM terminal to the XM Mini-Tuner system (sold

separately).

XM Mini-Tuner system

•Position the XM Mini-Tuner system near a south-facing window to receive the best signal.

When making connections, also refer to the operating instructions of the XM Mini-Tuner system.

•For the best reception, check the signal strength of the XM radio signal with using signal strength display mode, then adjust the position of the XM Mini-Tuner system until “GOOD” is displayed. (For details, refer to “Displaying XM information” on page 30.)

•To listen to XM Satellite Radio, refer to “XM Satellite Radio (only for North America)” on page 28.

9. CONNECTING SPEAKERS

•Be sure to connect speakers firmly and correctly according to the channel (left and right) and the polarity (+ and -). If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connection is incorrect, the sound will be unnatural and lack bass.

•For installing the speakers, refer to "Speaker placement" on page 10.

•After installing the speakers, first adjust the speaker settings according to your environment and speaker layout. (For details, refer to "SETTING THE SPEAKER SETUP" on page 41.)

Surround back speakers

•When using only one surround back speaker, you should connect it to SURROUND BACK LEFT channel.

In this case, you can connect a subwoofer without built-in amplifier to the SURROUND BACK RIGHT channel. (For details, refer to “When selecting the AMP ASSIGN” on page 37.)

Caution :

•Be sure to use the speakers with the impedance of 6 ohms or above.

•Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

R

L

R

L

R

L

9

Image 9

Contents RD-7502 Safety Instructions Introduction For Your SafetyRead this Before Operating Your Unit FCC InformationContents System Connections Connecting AntennasHDMIHigh Definition Multimedia Interface connection Connecting Video ComponentsConnecting Audio Components Connecting External INS Connecting Digital INS and OUTDigital input default settings Connecting DIGI-LINK Connecting Subwoofer PRE OUTConnecting XM only for North America Connecting SpeakersAC Input Cord Switched AC OutletsFront Panel Controls Fluorescent DisplayRemote Sensor Setup MIC Jack AUX in JackVideo 3 in Jacks Display button Remote ControlsLoading Batteries Remote Control Operation RangeWhen selecting the External in as desired OperationsBefore operation Reproduced through the headphones When CD, AUX, Video 1~2 is selected as an input sourceEnter the tone mode Adjusting the tone bass and trebleTone mode is displayed for several seconds Sources are input or the External in is selected canSurround Sound Dolby Pro Logic II surround Dolby Pro Logic IIx surroundDolby Virtual Speaker Dolby Pro LogicEnjoying Surround Sound Select the desired surround mode2CH downmix mode To cancel the surround mode for stereo operationControl can be set it 8 steps from 0 to 7 default value Pressed, the parameter mode changes as followsSP When using 2 front and center speakers Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersEnter the test tone mode Adjusting each channel level with test toneDolby Headphone Parameters SB orBL BR Adjusting the current channel levelMemorizing the adjusted channel levels Recalling the memorized channel levels1 of REF 1 indication flickers for several seconds Manual tuning Auto tuningAuto presetting Listening to Radio BroadcastsMemory Backup Function Manual presettingTuning to preset stations Scanning preset stations in sequenceXM Satellite Radio only for North America Signing up for XM Satellite RadioSelect XM Direct search Channel searchCategory search For 27 2Preset search Presetting channelsSignal strength display mode Error message and statusRecording Dubbing the audio and video signals separately onto VideoRecording with Tape Dubbing from video components onto VideoDigital Audio Recording with MD Recorder Start recording on the component connected toOptical Digital OUT Adjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Displaying the operation statusSystem Setup Navigating through the setup menuDown Setup menu flow is as follows Setup menu flowSystem Input SPK SETExit CH Level ParamtrSetting the System When selecting the AMP AssignWhen selecting the Subwoofer mode When selecting the Tone When selecting the Cinema EQPress the Cursor Left /RIGHT Setting the Input When selecting the DigitalInput When selecting the Auto Surround When selecting the Video ModeWhen selecting the Remaster When selecting the AV SyncWhen selecting the Auto Setup Setting the Speaker SetupPreparations About the first listening positionWhen the auto setup has been completed When performing the auto setupWhen selecting the Speaker Configuration When setting the speaker size by performing the auto setupSpeaker types When selecting the desired unit When selecting the Speaker DistanceWhen setting the distance About the speaker sizeAbout the crossover frequency When selecting the Speaker CrossoverButtons to select the desired speaker 40 ~ 200 Hz in 10 Hz intervalsOn When turning it on OFF When turning off the room EQ modeCH Level Setting the CH LevelRight UP /DOWNLower compression Higher compression Setting the Sound ParameterWhen selecting the Dolby Plii Music When selecting the Pano Panorama modeWhen selecting the C. Width Center width control When selecting the Dolby Headphone Each time the Cursor UP / Down buttons are pressedDH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the REF Dolby Virtual Speaker When selecting the Dolby Virtual SpeakerReference mode When selecting the Wide Dolby Virtual SpeakerProblem Possible Cause Remedy Troubleshooting GuideSpecifications RD-7502