Sherwood RD-7502 manual Digital Audio Recording with MD Recorder, Optical Digital OUT

Page 32

ENGLISH

Continued

3. Start recording on the VIDEO 1.

4. Start play on the VIDEO 2 and the CD respectively.

•The audio signal from the CD and the video signal from the VIDEO 2 will be dubbed and you can enjoy them on the TV set and from the speakers.

Note: Be sure to observe the order of the above steps 1 and 2.

DIGITAL AUDIO RECORDING WITH MD RECORDER

•Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to "CONNECTING VIDEO COMPONENTS", "CONNECTING AUDIO COMPONENTS" and "CONNECTING DIGITAL INS and OUT" on pages 6~8 and the operating instructions of the MD recorder or CD recorder.

Notes:

•Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc.

•In most DVDs as well as some CDs, etc., digital recording may not be available depending on the signal format.

•There are some restrictions on recording digital signals. When making digital recordings, refer to the operating instructions of your digital recording equipment to know what restrictions are imposed.

1. Select the desired of CD, AUX, VIDEO 1~2 as a

recording source.

SEL	ENTER	SEL
T
E
S
T
ST	SEARCH MODE	OU	N	D
ER		OU
	EO	RR
		SU
TONE	SOUND	EXT.IN		VIDEO 1 VIDEO 2
TONE	PARAMETER	EXT.IN
TAPE	VIDEO 1 VIDEO 2	VIDEO 3

FM/AM/XM CD AUX

CD AUX

REMOTE CONTROL RC-110

3. Start recording on the component connected to the

OPTICAL DIGITAL OUT.

2. For digital recording, select the digital input as recording

signal input.

		POWER ON		STANDBY
D/A MODE		2	3	SLEEP
		1
	D/A MODE	5	6	DIMMER
		5	6
		4
		8	9
		7
			MUTE
		P.SCAN		VOLUME
		0
		D/A MODE CH.LEVEL
		DISPLAY		SETUP
		SEL	ENTER	SEL
		T
		E
		S
		T
				D

Note :

•When the digital signals are not input from the selected digital input, there will be no recording.

(For details, refer to "When CD, AUX, VIDEO 1 ~ 2 is selected as an input source" on page 16.)

4.Start play on the desired input.

32

Image 32

Contents RD-7502 Safety Instructions For Your Safety IntroductionRead this Before Operating Your Unit FCC InformationContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Digital input default settings Connecting External INSConnecting Digital INS and OUT Connecting Subwoofer PRE OUT Connecting DIGI-LINKConnecting XM only for North America Connecting SpeakersSwitched AC Outlets AC Input CordRemote Sensor Front Panel ControlsFluorescent Display Video 3 in Jacks Setup MIC JackAUX in Jack Remote Controls Display buttonRemote Control Operation Range Loading BatteriesBefore operation When selecting the External in as desiredOperations When CD, AUX, Video 1~2 is selected as an input source Reproduced through the headphonesAdjusting the tone bass and treble Enter the tone modeTone mode is displayed for several seconds Sources are input or the External in is selected canSurround Sound Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby Pro LogicSelect the desired surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modePressed, the parameter mode changes as follows Control can be set it 8 steps from 0 to 7 default valueSP When using 2 front and center speakers Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersAdjusting each channel level with test tone Enter the test tone modeDolby Headphone Parameters SB orAdjusting the current channel level BL BR1 of REF 1 indication flickers for several seconds Memorizing the adjusted channel levelsRecalling the memorized channel levels Auto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionTuning to preset stations Scanning preset stations in sequenceSelect XM XM Satellite Radio only for North AmericaSigning up for XM Satellite Radio Channel search Direct searchCategory search For 27 2Presetting channels Preset searchSignal strength display mode Error message and statusDubbing the audio and video signals separately onto Video RecordingRecording with Tape Dubbing from video components onto VideoOptical Digital OUT Digital Audio Recording with MD RecorderStart recording on the component connected to Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the operation statusDown System SetupNavigating through the setup menu Setup menu flow Setup menu flow is as followsSystem Input SPK SETCH Level Paramtr ExitWhen selecting the Subwoofer mode Setting the SystemWhen selecting the AMP Assign Press the Cursor Left /RIGHT When selecting the ToneWhen selecting the Cinema EQ Input Setting the InputWhen selecting the Digital When selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsWhen performing the auto setup When the auto setup has been completedSpeaker types When selecting the Speaker ConfigurationWhen setting the speaker size by performing the auto setup When selecting the Speaker Distance When selecting the desired unitWhen setting the distance About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyButtons to select the desired speaker 40 ~ 200 Hz in 10 Hz intervalsOFF When turning off the room EQ mode On When turning it onSetting the CH Level CH LevelUP /DOWN RightSetting the Sound Parameter Lower compression Higher compressionWhen selecting the C. Width Center width control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode DH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the Dolby HeadphoneEach time the Cursor UP / Down buttons are pressed When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual SpeakerReference mode When selecting the Wide Dolby Virtual SpeakerTroubleshooting Guide Problem Possible Cause RemedySpecifications RD-7502