Sherwood RD-7502 manual Setup MIC Jack, AUX in Jack, Video 3 in Jacks

Page 12

ENGLISH

SETUP MIC JACK

•To use Auto Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When selecting the AUTO SETUP" on page 41.)

Notes:

•Because the microphone for Auto Setup is designed for use with this receiver, do not use a microphone other than the one supplied with this receiver.

•After you have completed the auto setup procedure, disconnect the microphone.

AUX IN JACK

•The AUX IN jack can be connected to an additional audio component such as an MP3 player, etc.

Note:

•When connecting this jack to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord.

VIDEO 3 IN JACKS

•The VIDEO 3 IN jacks may be also

connected to an additional video component such as a camcorder, video game player, etc.

When not using the VIDEO 3 IN jacks, cover these jacks with the supplied cap.

Image 12

Contents RD-7502 Safety Instructions For Your Safety IntroductionRead this Before Operating Your Unit FCC InformationContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Subwoofer PRE OUT Connecting DIGI-LINKConnecting XM only for North America Connecting SpeakersSwitched AC Outlets AC Input CordFront Panel Controls Fluorescent DisplayRemote Sensor Setup MIC Jack AUX in JackVideo 3 in Jacks Remote Controls Display buttonRemote Control Operation Range Loading BatteriesWhen selecting the External in as desired OperationsBefore operation When CD, AUX, Video 1~2 is selected as an input source Reproduced through the headphonesAdjusting the tone bass and treble Enter the tone modeTone mode is displayed for several seconds Sources are input or the External in is selected canSurround Sound Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby Pro LogicSelect the desired surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modePressed, the parameter mode changes as follows Control can be set it 8 steps from 0 to 7 default valueSP When using 2 front and center speakers Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersAdjusting each channel level with test tone Enter the test tone modeDolby Headphone Parameters SB orAdjusting the current channel level BL BRMemorizing the adjusted channel levels Recalling the memorized channel levels1 of REF 1 indication flickers for several seconds Auto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionTuning to preset stations Scanning preset stations in sequenceXM Satellite Radio only for North America Signing up for XM Satellite RadioSelect XM Channel search Direct searchCategory search For 27 2Presetting channels Preset searchSignal strength display mode Error message and statusDubbing the audio and video signals separately onto Video RecordingRecording with Tape Dubbing from video components onto VideoDigital Audio Recording with MD Recorder Start recording on the component connected toOptical Digital OUT Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the operation statusSystem Setup Navigating through the setup menuDown Setup menu flow Setup menu flow is as followsSystem Input SPK SETCH Level Paramtr ExitSetting the System When selecting the AMP AssignWhen selecting the Subwoofer mode When selecting the Tone When selecting the Cinema EQPress the Cursor Left /RIGHT Setting the Input When selecting the DigitalInput When selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsWhen performing the auto setup When the auto setup has been completedWhen selecting the Speaker Configuration When setting the speaker size by performing the auto setupSpeaker types When selecting the Speaker Distance When selecting the desired unitWhen setting the distance About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyButtons to select the desired speaker 40 ~ 200 Hz in 10 Hz intervalsOFF When turning off the room EQ mode On When turning it onSetting the CH Level CH LevelUP /DOWN RightSetting the Sound Parameter Lower compression Higher compressionWhen selecting the Dolby Plii Music When selecting the Pano Panorama modeWhen selecting the C. Width Center width control When selecting the Dolby Headphone Each time the Cursor UP / Down buttons are pressedDH 1 Dolby Headphone 1, DH 2 or DH 3 is selected When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual SpeakerReference mode When selecting the Wide Dolby Virtual SpeakerTroubleshooting Guide Problem Possible Cause RemedySpecifications RD-7502