Sherwood R-871 manual English

Page 28

Erasing all the punch-through functions programmed under a master device mode

Perform the steps ③ and ④ in

1“Entering a setup code” procedure on page 20 to select a master device and the punch-through mode (“PUNCH”).

•Then “VOL” is displayed on the LCD screen for several seconds.

While “DELETE” is displayed, to erase

3all the punch-through functions programmed under the master device mode, press ENTER button.

•Then “OK” is displayed and “DELETE” is displayed.

•To exit from the deleting mode, press any of the DEVICE buttons.

While “VOL” is displayed, press the

2CURSOR UP(▲)/DOWN(▼) buttons to select the all punch-through deleting mode (“DELETE”).

•Each time the CURSOR UP(▲)/DOWN(▼) buttons are pressed, the mode changes as follows:

→ VOL DELETE PLAY CH ←

• Then “DELETE” is displayed .

To erase all the punch-through

4functions programmed under other master device mode , repeat the above steps ① to ③.

ENGLISH

27

Image 28

Contents Page Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Connecting Audio Components Component Video Composite VideoConnecting Digital INS and OUT Connecting External INSDigital input default settings Connecting System Control Connecting PRE OutsConnecting DC Trigger OUT Front speakers a and B Connecting SpeakersSurround back speakers Speaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersConnecting Room 2 Outs Connecting PC for UpgradesConnecting MULTI-ROOM System KIT Connecting XM DT only for North AmericaSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeSearching a setup code Programing the commands from other Remote controls Learning modeErasing the programmed command Erasing all the commandsProgrammed under a device mode From one buttonProgramming a macro function Operating a macro functionTo erase a macro program To change a macro programProgramming a punch-through function → TV Delete SAT Cable VCR ←Operating a punch-through function Erasing the programmed puch-through functionEnglish Remote Control Operation Range Room 2 Remote ControlsLoading Battery When selecting the External in as desired OperationsListening to a Program Source Before operationWhen CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphonesAchieving higher purity of sound quality Surround modes Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby HeadphoneEnjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS WideListening in a Dolby Headphone mode Adjusting each channel level with test toneTo cancel the surround mode for stereo operation 2CH downmix modeAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionXM Satellite Radio only for North America Listening to XM Satellite RadioSigning up for XM Satellite Radio Whats XM Satellite Radio?Direct search Channel searchCategory search Preset search Presetting channelsDisplaying XM information Dubbing the audio and video signals RecordingRecording with Tape Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the audio informationRoom 2 Source Playback Input ~OSD Menu Settings Confirm your selection When selecting the items other than OSD Position Adjust Setting the System SetupWhen selecting the AMP Assign When selecting the Subwoofer Mode When selecting the Tone ControlWhen selecting the Cinema EQ When selecting the BackgroundWhen selecting the Momentary OSD When selecting the OSD Position AdjustSetting the Input Setup When selecting the items other than NameWhen selecting the Digital Audio When selecting the Video AssignWhen selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncWhen selecting the DC Trigger When selecting the NameSetting the Speaker / Room EQ Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker sizeWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Panorama mode When selecting the Dolby Plii MusicWhen selecting the Dimension control When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeSetting the Room 2 Setup When selecting the RoomWhen selecting the Input When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR STS DVD AUX-TAPE/MD AUX-HOME Automation