Sherwood R-871 manual English

Page 57

ENGLISH

Continued

Press the CURSOR UP(▲)/DOWN(▼) buttons to select the AUTO SETUP, then press the

2 ENTER button.

Press the CURSOR UP(▲)/DOWN(▼) buttons to select the START, then press the ENTER

3 button

When measurements at first position have been completed.

•Loud test tones are output from each speaker and then if measurements at the first position have been completed, "SECOND POSITION" message will be displayed.

Place the microphone on a flat level at the second main listening position.

4

•For optimum effectiveness, place the microphone at the second main position within the listening area surrounded by the speakers.

Press the CURSOR UP(▲)/DOWN(▼) buttons to select "CONTINUE", then press the ENTER

5 button

When the auto setup has been completed.

•Loud test tones are output again successively and then if a series of auto setup procedure has been completed, "COMPLETE" will be displayed.

•To stop the auto setup procedurewhile performing it, (press the CURSOR UP(▲)/DOWN(▼) buttons to select "CANCEL THE AUTO SETUP"), then press the ENTER button.

In such a case that the auto setup procedure is stopped before "COMPLETE", the results of each adjustment may not be memorized.

•If there may be a problem with front speakers or microphone connection, error message will be displayed. In this case, turn off the power, check the connection and then retry the auto setup procedure.

■Notes :

•Before starting auto setup, be sure not to set the SPEAKER button to off.

•Because the test tones are loud, ensure there no infants or small children in the room.

•For best results, ensure the room is as quiet as possible during the auto setup procedure. If there is too much ambient noise, the results may not be satisfactory.

56

Image 57

Contents Page Page Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasHdmi High Definition Multimedia Interface connection *1 Connecting Video ComponentsComponent Video Composite Video Connecting Audio ComponentsConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting PRE Outs Connecting System ControlConnecting DC Trigger OUT Connecting Speakers Front speakers a and BSurround back speakers Front left and right speakers and center speaker Speaker placementSurround left and right speakers Surround back left and right speakersConnecting PC for Upgrades Connecting Room 2 OutsConnecting XM DT only for North America Connecting MULTI-ROOM System KITAC Input Switched AC OutletsFluorescent Display Front Panel ControlsSetup MIC Jack Digi Link system remote controls Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Using Functions of Remote ControlSearching a setup code Remote controls Learning mode Programing the commands from otherErasing all the commands Erasing the programmed commandProgrammed under a device mode From one buttonOperating a macro function Programming a macro functionTo erase a macro program To change a macro program→ TV Delete SAT Cable VCR ← Programming a punch-through functionErasing the programmed puch-through function Operating a punch-through functionEnglish Room 2 Remote Controls Remote Control Operation RangeLoading Battery Operations When selecting the External in as desiredListening to a Program Source Before operationMuting the sound Listening with headphones When CD, AUX, Video 1~ 5 is selected as an input sourceAchieving higher purity of sound quality Surround modes Dolby Pro Logic II surround Dolby Pro Logic IIx surroundDolby Virtual Speaker Dolby HeadphoneDolby DIGITAL, Dolby VS REFERENCE, Dolby VS Wide Enjoying Surround SoundAdjusting each channel level with test tone Listening in a Dolby Headphone modeTo cancel the surround mode for stereo operation 2CH downmix modeAdjusting the current channel level Recalling the memorized channel levels Memorizing the adjusted channel levelsManual tuning Auto tuningAuto presetting Listening to Radio BroadcastsMemory Backup Function Manual presettingListening to XM Satellite Radio XM Satellite Radio only for North AmericaSigning up for XM Satellite Radio Whats XM Satellite Radio?Channel search Direct searchCategory search Presetting channels Preset searchDisplaying XM information Recording Dubbing the audio and video signalsRecording with Tape Dubbing from video components ontoDigital Audio Recording with MD Recorder Adjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Displaying the audio informationInput ~ Room 2 Source PlaybackOSD Menu Settings Confirm your selection Setting the System Setup When selecting the items other than OSD Position AdjustWhen selecting the AMP Assign When selecting the Tone Control When selecting the Subwoofer ModeWhen selecting the Background When selecting the Cinema EQWhen selecting the Momentary OSD When selecting the OSD Position AdjustWhen selecting the items other than Name Setting the Input SetupWhen selecting the Digital Audio When selecting the Video AssignWhen selecting the Auto Surround When selecting the Video ModeWhen selecting the Remaster When selecting the AV SyncWhen selecting the Name When selecting the DC TriggerWhen selecting the Auto Setup Setting the Speaker / Room EQ SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration About the speaker size When setting the speaker size by performing the auto setupAbout the speaker distance When selecting the Speaker DistanceAbout the crossover frequency When selecting the Speaker CrossoverWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels When selecting the Night Mode Setting the Sound ParameterWhen selecting the Dolby Plii Music When selecting the Panorama modeWhen selecting the Dimension control When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker Wide mode When selecting the Dolby Virtual SpeakerWhen selecting the Room Setting the Room 2 SetupWhen selecting the Input When selecting the VolumeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsAOC Setup Code TableVCR STS DVD AUX-TAPE/MD AUX-HOME Automation