Sherwood R-871 Listening in a Dolby Headphone mode, Adjusting each channel level with test tone

Page 36
Enter the test tone mode.

Continued

■To cancel the surround mode for stereo operation

• Depending on the signal format which is being input, either the stereo mode or the 2CH downmix mode is selected.

• To cancel either the stereo mode or the 2CH downmix mode, select the surround mode with using the MULTI CONTROL knob on the front panel or the SURROUND MODE UP/DOWN ( >/< ) buttons on the remote control.

■2CH downmix mode

•This mode allows the multi-channel signals encoded in DTS or Dolby Digital format to be mixed down into 2 front channels and to be reproduced through only two front speakers or through headphones.

•When the SPEAKER button is set to off to listen with headphones, if the STEREO button is pressed while playing the multi-channel digital signals from DTS or Dolby Digital sources, it will enter the 2CH downmix mode automatically.

•To cancel the 2CH downmix mode, select the desired Dolby Headphone mode with using the MULTI CONTROL knob on the front panel or the SURROUND MODE UP/DOWN ( >/< ) buttons on the remote control.

Listening in a Dolby Headphone mode

•The Dolby Headphone function simulates 5.1 channel surround sound, which allows you to enjoy 5.1 channel surround sound through 2 channel headphones, just like listening from 5.1 channel speakers.

■Notes :

•Only when the SPEAKER button is set to off, the Dolby Headphone mode can be selected.

•When playing the 96 kHz PCM(2 channel) digital signals, only the stereo mode can be selected.

•While listening with headphones, select the desired Dolby Headphone mode.

• Each time theMULTI CONTROL knob is rotated or the SURROUND MODE UP/DOWN ( >/< ) buttons are pressed, the mode changes as follows :

: This simulates the soundfield as if you were in a relatively

small room with less reverberations.

: This simulates the soundfield as if you were in a typical listening room with moderate reverberations.

: This simulates the soundfield as if you were in a large space like theater.

Adjusting each channel level with test tone

•The volume level of each channel can be adjusted easily with the test tone function. ■Note : When the SPEAKER button is set to off, the test tone function does not work.

• The test tone will be heard from the speaker of each

1

channel for 2 seconds as follows:

 

 

 

Front Left

Front Right

Surround Right

 

 

Subwoofer

Surround Left Surround Back

Surr.Back Left Surr.Back Right

 

• When the speaker setting is "NONE" or "NO", the test tone

 

of the corresponding channel is not available.

 

• (

) : Possible depending on whether the surround

 

 

back channel is set to "2 CH" or "1 CH".

2

At each channel, adjust the level as

3

Cancel the test tone function.

desired until the sound level of each

 

 

speaker is heard to be equally loud.

 

 

•You can select the desired channel with pressing the CONTROL UP/DOWN (▲/▼) buttons or the CURSOR UP/DOWN (▲/▼) buttons.

ENGLISH

35

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Page Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Connecting Audio Components Component Video Composite VideoConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting PRE Outs Connecting System ControlConnecting DC Trigger OUT Connecting Speakers Front speakers a and BSurround back speakers Speaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersConnecting Room 2 Outs Connecting PC for UpgradesConnecting MULTI-ROOM System KIT Connecting XM DT only for North AmericaSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeSearching a setup code Programing the commands from other Remote controls Learning modeErasing the programmed command Erasing all the commandsProgrammed under a device mode From one buttonProgramming a macro function Operating a macro functionTo erase a macro program To change a macro programProgramming a punch-through function → TV Delete SAT Cable VCR ←Operating a punch-through function Erasing the programmed puch-through functionEnglish Room 2 Remote Controls Remote Control Operation RangeLoading Battery When selecting the External in as desired OperationsListening to a Program Source Before operationWhen CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphonesAchieving higher purity of sound quality Surround modes Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby HeadphoneEnjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS WideListening in a Dolby Headphone mode Adjusting each channel level with test toneTo cancel the surround mode for stereo operation 2CH downmix modeAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionXM Satellite Radio only for North America Listening to XM Satellite RadioSigning up for XM Satellite Radio Whats XM Satellite Radio?Channel search Direct searchCategory search Presetting channels Preset searchDisplaying XM information Dubbing the audio and video signals RecordingRecording with Tape Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the audio informationRoom 2 Source Playback Input ~OSD Menu Settings Confirm your selection Setting the System Setup When selecting the items other than OSD Position AdjustWhen selecting the AMP Assign When selecting the Subwoofer Mode When selecting the Tone ControlWhen selecting the Cinema EQ When selecting the BackgroundWhen selecting the Momentary OSD When selecting the OSD Position AdjustSetting the Input Setup When selecting the items other than NameWhen selecting the Digital Audio When selecting the Video AssignWhen selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncWhen selecting the DC Trigger When selecting the NameSetting the Speaker / Room EQ Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker sizeWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Dolby Plii Music When selecting the Panorama modeWhen selecting the Dimension control When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeSetting the Room 2 Setup When selecting the RoomWhen selecting the Input When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR STS DVD AUX-TAPE/MD AUX-HOME Automation
Top Page Image Contents