Sherwood R-871 manual When selecting the Dolby Virtual Speaker

Page 68

When selecting the DOLBY VIRTUAL SPEAKER

•You can select the speaker layout to be used actually for each Dolby Virtual Speaker mode.

■Note:

•The speaker layout settings are valid only when listening in a Dolby Virtual Speaker mode.

Press the CURSOR UP(▲)/DOWN(▼) buttons to select the DOLBY VIRTUAL SPEAKER,

1 then press the ENTER button.

Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired Dolby Virtual Speaker mode.

2

Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired speaker layout.

3

■When selecting the Dolby Virtual Speaker Reference mode

2 SPK : When using 2 front speakers only.

3 SPK : When using 2 front and center speakers.

■When selecting the Dolby Virtual Speaker Wide mode

2 SPK : When using 2 front speakers only.

3 SPK : When using 2 front and center speakers.

4 SPK : When using 2 front and 2 surround speakers.

5 SPK : When using 2 front, center and 2 surround speakers.

■Note:

• When the speakers are set to "NONE", the corresponding speaker layouts cannot be selected.

4	Repeat the above steps ② and ③ to select the desired speaker layout for another Dolby
	Virtual Speaker mode.

ENGLISH

67

Image 68

Contents Page Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Connecting Audio Components Component Video Composite VideoDigital input default settings Connecting External INSConnecting Digital INS and OUT Connecting DC Trigger OUT Connecting PRE OutsConnecting System Control Surround back speakers Connecting SpeakersFront speakers a and B Speaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersConnecting Room 2 Outs Connecting PC for UpgradesConnecting MULTI-ROOM System KIT Connecting XM DT only for North AmericaSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeSearching a setup code Programing the commands from other Remote controls Learning modeErasing the programmed command Erasing all the commandsProgrammed under a device mode From one buttonProgramming a macro function Operating a macro functionTo erase a macro program To change a macro programProgramming a punch-through function → TV Delete SAT Cable VCR ←Operating a punch-through function Erasing the programmed puch-through functionEnglish Loading Battery Room 2 Remote ControlsRemote Control Operation Range When selecting the External in as desired OperationsListening to a Program Source Before operationWhen CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphonesAchieving higher purity of sound quality Surround modes Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby HeadphoneEnjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS WideListening in a Dolby Headphone mode Adjusting each channel level with test toneTo cancel the surround mode for stereo operation 2CH downmix modeAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionXM Satellite Radio only for North America Listening to XM Satellite RadioSigning up for XM Satellite Radio Whats XM Satellite Radio?Category search Channel searchDirect search Displaying XM information Presetting channelsPreset search Dubbing the audio and video signals RecordingRecording with Tape Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the audio informationRoom 2 Source Playback Input ~OSD Menu Settings Confirm your selection When selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the Subwoofer Mode When selecting the Tone ControlWhen selecting the Cinema EQ When selecting the BackgroundWhen selecting the Momentary OSD When selecting the OSD Position AdjustSetting the Input Setup When selecting the items other than NameWhen selecting the Digital Audio When selecting the Video AssignWhen selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncWhen selecting the DC Trigger When selecting the NameSetting the Speaker / Room EQ Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker sizeWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Dimension control When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeSetting the Room 2 Setup When selecting the RoomWhen selecting the Input When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR STS DVD AUX-TAPE/MD AUX-HOME Automation