Sherwood R-871 manual OSD Menu Settings

Page 48

OSD Menu Settings

•The OSD (On-Screen Display) menu is a setting menu that is displayed on the monitor TV and allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later.

The OSD menu consists of 6 main menus ; system setup, input setup, speaker / room EQ setup, CH level setup, sound parameter and room 2 setup. These menus are then divided up into various sub-menus.

■Notes:

•The OSD menu and the momentary OSD cannot be diplayed via MONITOR HDMI OUT connector.

•Depending on the VIDEO MODE setting and the video connections between this receiver and the video component, the OSD menu and the momentary OSD cannot be displayed via MONITOR COMPOSITE OUT jack, or the picture is automatically turned off and only the OSD menu can be displayed via MONITOR COMPONENT OUT jacks.

(For details, refer to "Relationship between the video input signal and the video output signal" on page 7.)

■Navigating through the OSD menu

•The explanations here assume you are using the buttons on the remote control when performing the OSD menu operation. However, you can use the buttons on the front panel as well.

The buttons on the front panel correspond to those on the remote control as shown below.

Turn the menu screen on.

1

ENGLISH

•The main menu will be shown.

•To turn the menu screen off, press this button again.

Select the desired menu using the

2 CURSOR UP(▲)/DOWN(▼) buttons.

47

Image 48

Contents Page Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Connecting Audio Components Component Video Composite VideoConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting PRE Outs Connecting System ControlConnecting DC Trigger OUT Connecting Speakers Front speakers a and BSurround back speakers Speaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersConnecting Room 2 Outs Connecting PC for UpgradesConnecting MULTI-ROOM System KIT Connecting XM DT only for North AmericaSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeSearching a setup code Programing the commands from other Remote controls Learning modeErasing the programmed command Erasing all the commandsProgrammed under a device mode From one buttonProgramming a macro function Operating a macro functionTo erase a macro program To change a macro programProgramming a punch-through function → TV Delete SAT Cable VCR ←Operating a punch-through function Erasing the programmed puch-through functionEnglish Room 2 Remote Controls Remote Control Operation RangeLoading Battery When selecting the External in as desired OperationsListening to a Program Source Before operationWhen CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphonesAchieving higher purity of sound quality Surround modes Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby HeadphoneEnjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS WideListening in a Dolby Headphone mode Adjusting each channel level with test toneTo cancel the surround mode for stereo operation 2CH downmix modeAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionXM Satellite Radio only for North America Listening to XM Satellite RadioSigning up for XM Satellite Radio Whats XM Satellite Radio?Channel search Direct searchCategory search Presetting channels Preset searchDisplaying XM information Dubbing the audio and video signals RecordingRecording with Tape Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the audio informationRoom 2 Source Playback Input ~OSD Menu Settings Confirm your selection Setting the System Setup When selecting the items other than OSD Position AdjustWhen selecting the AMP Assign When selecting the Subwoofer Mode When selecting the Tone ControlWhen selecting the Cinema EQ When selecting the BackgroundWhen selecting the Momentary OSD When selecting the OSD Position AdjustSetting the Input Setup When selecting the items other than NameWhen selecting the Digital Audio When selecting the Video AssignWhen selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncWhen selecting the DC Trigger When selecting the NameSetting the Speaker / Room EQ Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker sizeWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Dolby Plii Music When selecting the Panorama modeWhen selecting the Dimension control When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeSetting the Room 2 Setup When selecting the RoomWhen selecting the Input When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR STS DVD AUX-TAPE/MD AUX-HOME Automation