Sherwood R-871 manual Programming a punch-through function, → TV Delete SAT Cable VCR ←

Page 26

Programming a punch-through function

•The punch-through function allows the volume controls, channel controls or transport controls to link to a different device while a device is controlled with this remote control as a master device.

•For example, since this receiver will likely be used as the sound system while watching TV, you may want to use volume controls to operate this receiver although this remote control is set to control the TV.

Perform the steps ③ and ④ in

1“Entering a setup code” procedure on page 20 to select a master device and the punch -through mode (“PUNCH”).

•Then “VOL” is displayed on the LCD screen for several seconds.

While the device is displayed, press the

3CURSOR UP(▲)/DOWN(▼) buttons to select the desired punch-through device, then press the ENTER button.

•Each time theCURSOR UP(▲)/DOWN(▼) buttons are pressed, depending on the selected punch-through mode, punch-through devices and the one punch-through deleting mode (“DELETE”) are selected as follows :

•In case of the volume punch-through,

→ AUDIO DELETE TV ←

• In case of the transport punch-through,

→ CD DELETE DVD VCR AUX ←

• In case of the channel punch-through,

→ TV DELETE SAT CABLE VCR ←

•Then “OK” is displayed and the current punch- through mode is displayed.

While “VOL” is displayed, press the

2CURSOR UP(▲)/DOWN(▼) buttons to select the desired punch-through mode , then press the ENTER button.

•Each time the CURSOR UP(▲)/DOWN(▼) buttons are pressed, the mode changes as follows:

→VOL : The volume punch -through mode allows the “VOLUME ▲/▼” and “MUTE” buttons to operate a different device.

DELETE : All punch-through deleting mode.

PLAY : The transport punch-through mode allows the “◀◀”, “●”, “▶▶”, “■◀◀”, “■”, “▶▶■”, “◀/■■” and “▶” buttons to operate a different device.

→CH : The channel punch-through mode allows the “CHANNEL ∧/∨” and “CH. LEVEL” buttons to operate a different device.

•Then the device to which you can link the selected punch-through mode is displayed.

While the punch-through mode is

4displayed, repeat the above steps ② and ③ to program other punch-through function under the same master device mode.

To program punch-through functions

5under other master device mode, repeat the above steps ① to ④.

ENGLISH

25

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Page Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Connecting Audio Components Component Video Composite VideoDigital input default settings Connecting External INSConnecting Digital INS and OUT Connecting DC Trigger OUT Connecting PRE OutsConnecting System Control Surround back speakers Connecting SpeakersFront speakers a and B Surround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersConnecting Room 2 Outs Connecting PC for UpgradesConnecting MULTI-ROOM System KIT Connecting XM DT only for North AmericaSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeSearching a setup code Programing the commands from other Remote controls Learning modeProgrammed under a device mode Erasing the programmed commandErasing all the commands From one buttonTo erase a macro program Programming a macro functionOperating a macro function To change a macro programProgramming a punch-through function → TV Delete SAT Cable VCR ←Operating a punch-through function Erasing the programmed puch-through functionEnglish Loading Battery Room 2 Remote ControlsRemote Control Operation Range Listening to a Program Source When selecting the External in as desiredOperations Before operationWhen CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphonesAchieving higher purity of sound quality Surround modes Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby HeadphoneEnjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS WideTo cancel the surround mode for stereo operation Listening in a Dolby Headphone modeAdjusting each channel level with test tone 2CH downmix modeAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsManual presetting Memory Backup FunctionSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaListening to XM Satellite Radio Whats XM Satellite Radio?Category search Channel searchDirect search Displaying XM information Presetting channelsPreset search Recording with Tape Dubbing the audio and video signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Displaying the audio informationRoom 2 Source Playback Input ~OSD Menu Settings Confirm your selection When selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the Subwoofer Mode When selecting the Tone ControlWhen selecting the Momentary OSD When selecting the Cinema EQWhen selecting the Background When selecting the OSD Position AdjustWhen selecting the Digital Audio Setting the Input SetupWhen selecting the items other than Name When selecting the Video AssignWhen selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncWhen selecting the DC Trigger When selecting the NameAbout the first listening position Setting the Speaker / Room EQ SetupWhen selecting the Auto Setup PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker sizeWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Dimension control When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeWhen selecting the Input Setting the Room 2 SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR STS DVD AUX-TAPE/MD AUX-HOME Automation
Top Page Image Contents