Sherwood R-871 manual Other Functions, Operating the sleep timer, Displaying the audio information

Page 46

OTHER FUNCTIONS

Operating the sleep timer

The sleep timer allows the system to continue to operate for a specified period of time before automatically shutting off.

To set the receiver to automatically turn off after the specified period of time.

Each time this button is pressed, the sleep time changes as follows:

10 20 30 --- 90 OFF

Unit : minutes

•While operating the sleep timer, " " lights up.

When the sleep time is selected, all display panels of Sherwood components connected by the DIGI LINK III are dimly lit.

Adjusting the brightness of the fluorescent displays

Each time this button is pressed, the brightness of all fluorescent displays of Sherwood components connected by the DIGI LINK III changes together as follows:

ON dimmer OFF

In the display OFF mode, pressing any button will cancel the display OFF mode for several seconds to display the operation status.

ENGLISH

Displaying the audio information

You can check the audio information of the input source other than tuner on your monitor TV.

During playback,

Depending on whether the input signal is digital or analog signal, the corresponding information is

displayed for several seconds.

Example : When playing the digital signals from the

Dolby Digital source.

45

Image 46
Contents Page Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Connecting Audio Components Component Video Composite VideoConnecting Digital INS and OUT Connecting External INSDigital input default settings Connecting System Control Connecting PRE OutsConnecting DC Trigger OUT Front speakers a and B Connecting SpeakersSurround back speakers Surround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersConnecting Room 2 Outs Connecting PC for UpgradesConnecting MULTI-ROOM System KIT Connecting XM DT only for North AmericaSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeSearching a setup code Programing the commands from other Remote controls Learning modeProgrammed under a device mode Erasing the programmed commandErasing all the commands From one buttonTo erase a macro program Programming a macro functionOperating a macro function To change a macro programProgramming a punch-through function → TV Delete SAT Cable VCR ←Operating a punch-through function Erasing the programmed puch-through functionEnglish Remote Control Operation Range Room 2 Remote ControlsLoading Battery Listening to a Program Source When selecting the External in as desiredOperations Before operationWhen CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphonesAchieving higher purity of sound quality Surround modes Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby HeadphoneEnjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS WideTo cancel the surround mode for stereo operation Listening in a Dolby Headphone modeAdjusting each channel level with test tone 2CH downmix modeAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsManual presetting Memory Backup FunctionSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaListening to XM Satellite Radio Whats XM Satellite Radio?Direct search Channel searchCategory search Preset search Presetting channelsDisplaying XM information Recording with Tape Dubbing the audio and video signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Displaying the audio informationRoom 2 Source Playback Input ~OSD Menu Settings Confirm your selection When selecting the items other than OSD Position Adjust Setting the System SetupWhen selecting the AMP Assign When selecting the Subwoofer Mode When selecting the Tone ControlWhen selecting the Momentary OSD When selecting the Cinema EQWhen selecting the Background When selecting the OSD Position AdjustWhen selecting the Digital Audio Setting the Input SetupWhen selecting the items other than Name When selecting the Video AssignWhen selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncWhen selecting the DC Trigger When selecting the NameAbout the first listening position Setting the Speaker / Room EQ SetupWhen selecting the Auto Setup PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker sizeWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Panorama mode When selecting the Dolby Plii MusicWhen selecting the Dimension control When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeWhen selecting the Input Setting the Room 2 SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR STS DVD AUX-TAPE/MD AUX-HOME Automation