GE JBP77, JBP63, JBP76, JBP75 owner manual Before After

Page 37

5 4-Wire Power Cord Installation

WARNING: The neutral wire of the supply circuit is connected to the neutral terminal located in the center of the connector block. The power leads must be connected to the outside (brass colored) terminals. The 4th grounding lead must be connected

to the frame of the range with the grounding plate and grounding screw.

a Remove the 3 screws from the connector block.

	Remove the grounding screw and strap from the connector block middle
b
	location and the screw connection to the frame of the range.
	Insert screws through each power cord terminal ring and into connector
c
	block until screw engages nut. Be certain that the center wire is connected
	to the center screw of the connector block. Tighten screws securely.

d Attach ground wire to the frame of the range.

Before	After
Neutral terminal	Neutral terminal

Grounding

plate

Ground Strap

(grounding to range)

Grounding to range

Safety Information Operating Instructions Installation Instructions Troubleshooting Tips Customer Service

37

Image 37

Contents GE Answer Center GE AppliancesCongratulations You Are Now Part of the GE Family Staple sales slip or cancelled check hereWrite the model and serial numbers here You can find them on a label behindGE & You Service Partnership Small amount of carbon monoxide during the cleaning cycle Fiberglass insulation in self-clean ovens gives off a veryAll ranges can tip and injury could result California Safe Drinking Water and Toxic EnforcementSafety Precautions Safety Information When Cooking PORK… Oven SELF-CLEANING Oven Radiant Surface Units Page Instructions Safety Information REMEMBER… How to Set Using the surface unitsIndicator Lights About the radiant surface units…Selecting types of cookware Instructions Using the oven controlsOven on Light Oven Control SettingsBefore you begin… Using the ovenHow to Set the Oven for Broiling Preheating and Pan PlacementTroubleshooting Tips Customer Service Aluminum FoilComments Broiling guideUsing the clock and timer Make sure the oven clock shows the correct time of day Automatic StopPress Cook Time ON/OFF Press Start Time ON/OFFFor Models with Pads and an Oven Temperature Knob For Models with Only an Oven Temperature KnobLatch Door Indicates the thermostat will be set 20F. cooler Before a Clean Cycle Using the self-cleaning ovenCustomer Service Troubleshooting How to Set the Oven for CleaningAfter a Clean Cycle How to Delay the Start of CleaningTroubleshooting Tips Customer Service Press the Start Time ON/OFF padControl Panel and Knobs Care and cleaning of the rangeOven Vent Painted SurfacesTo clean the outside of the door To clean the inside of the doorLift-Off Oven Door Do not lift the door by the handleOven Heating Elements Oven Light Replacement on some modelsOven Shelves To remove the coverTo remove the storage drawer Broiler Pan & GridTo replace the storage drawer Daily Cleaning Cleaning the glass cooktopFor heavy, burned-on soil National Parts CenterSpecial Care Wiring must conform to National Electric Codes Installation of the rangePrepare the Opening Prepare for Electrical Connection Flooring Under the RangeStrain relief, they can be removed for better fit Power Cord Strain Relief InstallationDo not remove ground strap connection Wire Power Cord InstallationBefore After Wire Conduit Installation Connector block terminal Bare wire Leveling the Range Anti-Tip Bracket InstallationFinal Check Before you call for service… When range is Blank or indicatorFrequent cycling Off and onOr roast properly Food does not bakeFood does not Broil properly At BroilClock and timer Oven temperatureSelf-clean Self-clean cycleAfter a clean cycle Oven not cleanExcessive smoking Oven door willPower outage Is on when youWant to cook A numberFive Years Replacement glass cooktop if it should crack due GE Electric Range WarrantyWe Will Replace, At No Charge To You What GE Will Not CoverIn-Home Repair Service 800-GE-CARES Service Telephone NumbersTDD 800-TDD-GEAC