GE 49-8726, 164D2966P238 warranty Step

Page 36

INSTALLATION INSTRUCTIONS

(continued)

PREPARE THE OPENING (continued)

Flooring Under the Range

Your range, like many other household items, is heavy and can settle into soft floor coverings such as cushioned vinyl or carpeting. When moving the range on this type of flooring, it should be installed on a 1/4 inch thick sheet of plywood (or similar material) as follows:

When the floor covering ends at the front of the range, the area that the range will rest on should be built up with plywood to the same level or higher than the floor covering. This will allow the range to be moved for cleaning or servicing.

STEP 2

PREPARE FOR ELECTRICAL CONNECTION

Effective January 1, 1996 the National Electric Code requires that new construction (not existing) utilize a 4 conductor connection to an electric range. When installing an electric range in new construction follow Steps 3 and 5 for 4 wire connection.

Use only 3-conductor or 4-conductor U.L. listed range cord. These cords may be provided with ring terminals on wire and strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord is not recommended but if used, it should be marked for use with nominal 13⁄8″ diameter connection openings. Care should be taken to center cable and strain relief within knockout hole to keep the edge from damaging the cable.

NOTE: A 4-conductor cord is to be used when the appliance is installed in a mobile home or when local codes do not permit grounding through the neutral. If conduit is being used, go to Step 6 or 7.

STEP 3

POWER CORD STRAIN RELIEF INSTALLATION

A.Remove the lower rear range wiring cover to expose the connector block and bracket.

B.Remove the knockout ring (13⁄8″) located on bracket directly below the connector. To remove the knockout, use a pair of pliers to bend the knockout ring away from the bracket and twist until ring is removed.

36

BEFORE

KNOCKOUT

RING

BRACKET

AFTER

KNOCKOUT

RING

REMOVED

C.Assemble the strain relief in the hole. Insert the power cord through the strain relief and tighten. Allow enough slack to easily attach the cord terminals to the connector block. If tabs are present at the end of the winged strain relief, they can be removed for better fit.

NOTE: Do not install the power cord without a strain relief.

WIRING COVER (SHOWN REMOVED)

CONNECTOR

BLOCK

GROUND

STRAP

STRAIN

RELIEF

BRACKET

POWER CORD

STRAIN RELIEF

BRACKET (PROVIDED

WITH RANGE CORD.

NOT PART OF RANGE.)

Page 35 Page 37
Image 36
Page 35 Page 37
Contents UseandCare& Installation Guide If YOU Need SERVICE… Help US Help YOU…Important Safety Instructions Read all instructions before using this applianceSelf-Cleaning Oven OvenSave These Instructions Cooktop and Radiant Surface UnitsFeatures of Your Range JBP63Automatic Oven Light Switch Oven Interior Light ExplainedStorage Drawer Anti-Tip Device Broil Element Oven Door LatchHOW does this Cooktop Compare To Your OLD ONE? Type of Cooktop Description How It Works RadiantHot Surface Indicator Light General Information About Radiant Surface UnitsHow to Set the Controls Cooking Guide for Using Heat SettingsSurface unit on indicator light will glow Surface ControlsSurface Cookware Tips Types of CookwareCopper Bottom Porcelain/enamelHow to Check Pan Performance Special Cautions for Glass CooktopsHome Canning Tips Observe the Following Points in CanningCanning should be done on the cooktop only Flat-bottomed canners are required for glass cooktopsGlass Cooktop Cleaning Glass Cooktop CleaningFor normal, light soil For heavy, burned on soilAutomatic Timers and Clock Minute TimerTo Set the Minute Timer Questions and AnswersUsing Your Oven Before Using Your OvenOven Controls Oven ShelvesShelf Positions Oven LightHow to Set Your Range for Baking BakingType of Food Shelf Position Pan Placement PreheatingBaking Pans Baking GuidesPies CakesAluminum Foil Don’t PeekHow to Time Bake How to Set Immediate Start and Automatic StopTimed Baking How to Set Delay Start and Automatic Stop Adjust the Oven Thermostat To Adjust the ThermostatRoasting Use of Aluminum FoilWhy is my roast crumbling when I try to carve it? Roasting GuideFrozen Roasts Why are my meats not turning out as brown as they should? BroilingShould I salt the meat before broiling? Broiling Guide Oven door should be open to the broil stop positionOperating the SELF-CLEANING Oven Before a Clean CycleNormal Cleaning Time 3 hours Quick Reminder How to Set the Oven for Cleaning To Stop a Clean CycleSelf After a Clean Cycle Should there be any odor during the cleaning?Why do I have ash left in my oven after cleaning? My oven shelves do not slide easily. What is the matter?Care and Cleaning Oven Light ReplacementTo remove To replace coverDo not clean the bake element or the broil element Lift-Off Oven DoorOven Heating Elements Inside of the doorBroiler Pan and Grid Control Panel and Knobs Oven VentMetal Parts Painted SurfacesInstallation Instructions Before YOU BeginStep Step Wire Power Cord Installation Step Wire Conduit Installation Step Final Check QUESTIONS? USE this Problem Solver Problem Possible CauseProblem Solver Problem Solver SELF-CLEANWe’ll Be There Warranty

164D2966P238, 49-8726 specifications

The GE 49-8726,164D2966P238 is a high-performance component designed for various industrial applications, showcasing advanced technologies and engineering excellence. This product is a testament to General Electric’s commitment to innovation and reliability in the field of electrical equipment.

At its core, the GE 49-8726,164D2966P238 is engineered to provide superior performance in a compact form factor, making it suitable for a variety of demanding environments. One of the most notable features of this product is its robust construction. Built with high-quality materials, it offers excellent durability and resistance to harsh conditions. This makes it ideal for use in industries such as manufacturing, energy, and transportation.

The device incorporates state-of-the-art technologies that enhance its functionality and efficiency. One of the key technologies used in the GE 49-8726,164D2966P238 is advanced thermal management, which ensures optimal operating temperatures, even under heavy loads. This feature significantly reduces the risk of overheating, thereby prolonging the lifespan of the component and ensuring consistent performance.

Another critical characteristic of the GE 49-8726,164D2966P238 is its adaptability. It can be integrated into various systems without the need for extensive modifications, providing flexibility in installation. This enables businesses to streamline their operations and minimize downtime, as the component can be easily replaced or upgraded.

In terms of electrical performance, the GE 49-8726,164D2966P238 boasts impressive specifications, including high wattage ratings and low power consumption. This not only enhances energy efficiency but also reduces operational costs, making it a cost-effective solution for enterprises looking to enhance their productivity without compromising on quality.

Safety is also a paramount consideration in the design of the GE 49-8726,164D2966P238. It includes various safety features that comply with industry standards, ensuring safe operations in potentially hazardous environments. These features protect both the equipment and the personnel involved in its operation.

In conclusion, the GE 49-8726,164D2966P238 stands out as a top-tier component characterized by its advanced technologies, robust construction, and exceptional performance. Its versatility and reliability make it an excellent choice for industries that demand high-quality solutions for their operational needs.
Top Page Image Contents