GE 164D2966P238, 49-8726 warranty Installation Instructions, Before YOU Begin

Page 35

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT: Save these instructions for the local electrical inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE TO INSTALLER: Leave these instructions with the appliance after installation is completed.

NOTE TO CONSUMER: Keep this Use and Care Guide and Installation Instructions for future use.

NOTE: This appliance must be properly grounded.

TOOLS YOU WILL NEED

•Large blade screwdriver

•Channel lock pliers or small ratchet wrench with 3/16-inch socket (for leveling range)

•1/4-inch hex head nutdriver

ELECTRICAL REQUIREMENTS

CAUTION, FOR PERSONAL SAFETY:

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION.

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or time delay fuse, as noted on the rating plate.

Wiring must conform to National Electric Codes.

If the electric service provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet.

Because range terminals are not accessible after range is in position, flexible service conduit or cord must be used.

STEP 1

PREPARE THE OPENING

11⁄2 inch spacing is recommended from the range to adjacent vertical walls above cooktop surface.

Allow 30 inches minimum clearance between surface units and bottom of unprotected wood or metal top cabinet, and 15 inches minimum between countertop and adjacent cabinet bottom.

EXCEPTION: Installation of a listed microwave oven or cooking appliance over the cooktop shall conform to the installation instructions packed with that appliance.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a min. of 5 inches beyond the bottom of the cabinets. Make sure the wall covering, countertops and cabinets around the range can withstand heat generated by the range, oven or cooktop up to 200°F.

NOT LESS THAN

WIDTH OF RANGE

 

 

 

 

 

 

 

HOOD

 

 

 

 

 

 

 

 

5″ MIN.

30″

 

 

 

 

 

 

 

 

MIN. 15″

 

 

 

 

 

 

 

 

MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCATE

 

 

 

 

 

 

 

 

OUTLET BOX

WALL

 

 

 

 

 

 

WITHIN EITHER

 

 

 

 

 

 

SHADED AREA

 

1

1

2″

 

 

 

 

 

 

 

⁄

 

 

 

 

 

 

MIN.

 

 

 

 

 

INSTALL

 

 

 

 

 

 

 

 

OUTLET BOX

 

 

 

 

 

 

 

ON EITHER

WALL

C OF RANGE

 

 

 

SIDE OF C

 

 

 

L

 

 

 

 

L

 

 

1

2″

 

 

 

 

 

 

 

7 ⁄

 

 

 

 

OUTLET

7″

7

1 2″

145⁄8″

 

 

⁄

 

 

BOX

 

 

3

1

2″

 

 

 

 

 

 

 

⁄

5″

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

4″

 

 

 

 

 

 

 

2 ⁄

CORD FLOOR

Anti-Tip Bracket

(install in either rear corner)

(continued next page)

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents UseandCare& Installation Guide Help US Help YOU… If YOU Need SERVICE…Read all instructions before using this appliance Important Safety InstructionsOven Self-Cleaning OvenCooktop and Radiant Surface Units Save These InstructionsJBP63 Features of Your RangeBroil Element Oven Door Latch Automatic Oven Light Switch Oven Interior LightExplained Storage Drawer Anti-Tip DeviceType of Cooktop Description How It Works Radiant HOW does this Cooktop Compare To Your OLD ONE?General Information About Radiant Surface Units Hot Surface Indicator LightSurface Controls How to Set the ControlsCooking Guide for Using Heat Settings Surface unit on indicator light will glowPorcelain/enamel Surface Cookware TipsTypes of Cookware Copper BottomSpecial Cautions for Glass Cooktops How to Check Pan PerformanceFlat-bottomed canners are required for glass cooktops Home Canning TipsObserve the Following Points in Canning Canning should be done on the cooktop onlyFor heavy, burned on soil Glass Cooktop CleaningGlass Cooktop Cleaning For normal, light soilQuestions and Answers Automatic Timers and ClockMinute Timer To Set the Minute TimerOven Shelves Using Your OvenBefore Using Your Oven Oven ControlsOven Light Shelf PositionsType of Food Shelf Position How to Set Your Range for BakingBaking Baking Guides Pan PlacementPreheating Baking PansDon’t Peek PiesCakes Aluminum FoilTimed Baking How to Time BakeHow to Set Immediate Start and Automatic Stop How to Set Delay Start and Automatic Stop To Adjust the Thermostat Adjust the Oven ThermostatUse of Aluminum Foil RoastingFrozen Roasts Why is my roast crumbling when I try to carve it?Roasting Guide Should I salt the meat before broiling? Why are my meats not turning out as brown as they should?Broiling Oven door should be open to the broil stop position Broiling GuideNormal Cleaning Time 3 hours Quick Reminder Operating the SELF-CLEANING OvenBefore a Clean Cycle Self How to Set the Oven for CleaningTo Stop a Clean Cycle My oven shelves do not slide easily. What is the matter? After a Clean CycleShould there be any odor during the cleaning? Why do I have ash left in my oven after cleaning?To replace cover Care and CleaningOven Light Replacement To removeInside of the door Do not clean the bake element or the broil elementLift-Off Oven Door Oven Heating ElementsBroiler Pan and Grid Painted Surfaces Control Panel and KnobsOven Vent Metal PartsBefore YOU Begin Installation InstructionsStep Step Wire Power Cord Installation Step Wire Conduit Installation Step Final Check Problem Possible Cause QUESTIONS? USE this Problem SolverProblem Solver SELF-CLEAN Problem SolverWe’ll Be There Warranty

164D2966P238, 49-8726 specifications

The GE 49-8726,164D2966P238 is a high-performance component designed for various industrial applications, showcasing advanced technologies and engineering excellence. This product is a testament to General Electric’s commitment to innovation and reliability in the field of electrical equipment.

At its core, the GE 49-8726,164D2966P238 is engineered to provide superior performance in a compact form factor, making it suitable for a variety of demanding environments. One of the most notable features of this product is its robust construction. Built with high-quality materials, it offers excellent durability and resistance to harsh conditions. This makes it ideal for use in industries such as manufacturing, energy, and transportation.

The device incorporates state-of-the-art technologies that enhance its functionality and efficiency. One of the key technologies used in the GE 49-8726,164D2966P238 is advanced thermal management, which ensures optimal operating temperatures, even under heavy loads. This feature significantly reduces the risk of overheating, thereby prolonging the lifespan of the component and ensuring consistent performance.

Another critical characteristic of the GE 49-8726,164D2966P238 is its adaptability. It can be integrated into various systems without the need for extensive modifications, providing flexibility in installation. This enables businesses to streamline their operations and minimize downtime, as the component can be easily replaced or upgraded.

In terms of electrical performance, the GE 49-8726,164D2966P238 boasts impressive specifications, including high wattage ratings and low power consumption. This not only enhances energy efficiency but also reduces operational costs, making it a cost-effective solution for enterprises looking to enhance their productivity without compromising on quality.

Safety is also a paramount consideration in the design of the GE 49-8726,164D2966P238. It includes various safety features that comply with industry standards, ensuring safe operations in potentially hazardous environments. These features protect both the equipment and the personnel involved in its operation.

In conclusion, the GE 49-8726,164D2966P238 stands out as a top-tier component characterized by its advanced technologies, robust construction, and exceptional performance. Its versatility and reliability make it an excellent choice for industries that demand high-quality solutions for their operational needs.
Top Page Image Contents