GE 49-8779, 164D3333P033 manual Anti-Tip Bracket Installation, Leveling the Range, Final Check

Page 52

8 Anti-Tip Bracket Installation

Customer Service Troubleshooting Tips Installation Instructions Operating Instructions Safety Information

Installation of the range.

Read these instructions completely and carefully.

8 Anti-Tip Bracket Installation

An Anti-Tip bracket is supplied with instructions for installation in a variety of locations. The instructions include a template, a parts list and a list of tools necessary to complete the installation. Read the Important Safety Information and the instructions that fit your situation before beginning installation.

WARNING

■Range must be secured by Anti-Tip bracket supplied.

■See instructions to install (supplied with bracket).

■Unless properly installed, the range could be tipped by stepping or sitting on the door. Injury might result from spilled hot liquids or from the range itself.

Bracket

Wall plate

Screw must enter wood or metal

Typical installation of anti-tip bracket attachment to wall.

9 Leveling the Range

The range must be level. Leveling feet are located at each corner of the base of the range. Remove the storage drawer or kick panel (depending on your model) and using channel locks, rotate the leveling feet in and out as required to level the range. (For instructions on how to remove and replace the storage drawer or the kick panel, see the Care and cleaning of the range section.)

On some models, there are plastic covers which may be removed for easy adjustment (just squeeze and pull).

One of the rear leveling feet will engage the Anti-Tip bracket (allow for some side to side adjustment). Allow a minimum clearance of 1/8″ between the range and the leveling foot that is to be installed into the Anti-Tip bracket.

Check the range for proper installation into the Anti-Tip bracket by removing the kick panel or storage drawer and inspecting the rear leveling leg. Make sure it fits securely into the slot.

10 Final Check

Be sure all range controls are in the OFF position before leaving the range.

52

Image 52

Contents GE Appliances GE Answer CenterOwner’s Manual JBP90 JBP95Staple sales slip or cancelled check here Congratulations You Are Now Part of the GE FamilyWrite the model and serial numbers here # # drawerGE & You A Service Partnership Troubleshooting TipsIf You Need Service Safety InformationIMPORTANT SAFETY NOTICE IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USINGor using a ventilation fan or hood WARNING ANTI-TIP DEVICESAFETY PRECAUTIONS Safety Information OperatingSafety Information WHEN COOKING PORK… Safety Information Operating Instructions InstallationOVEN SELF-CLEANING OVEN Instructions Safety Information HALOGEN/RADIANT SURFACE UNITSAlways turn the surface units off before removing cookware Customer Service Instructions Safety InformationCleaning the glass cooktop section HALOGEN/RADIANT SURFACE UNITSUsing the surface units SafetyHow to Set Indicator LightsInstructions Operating Instructions Safety Information Dual Surface Unit SwitchDifferences Between Halogen and Radiant Units Temperature LimiterSelecting types of cookware Stainless SteelAluminum Copper BottomUsing the oven controls TIMER ON/OFFSTOP TIME CLOCKOven Control Settings AUTO SELF CLEANBROIL HI/LO Pad CONV. ROAST PadUsing the oven Safety InformationD C B A Operating InstructionsPreheating and Pan Placement Safety Information Operating Instructions Installation InstructionsHow to Set the Oven for Broiling Aluminum FoilBroiling guide ShelfFirst Side FoodUsing the clock and timer InstallationTo Set the Timer To Reset the TimerUsing the timed baking and roasting features How to Set an Immediate Start and Automatic StopHow to Set a Delay Start and Automatic Stop Make sure the oven clock shows the correct time of dayUsing the probe Instructions SafetyInformation Do not store the probe in the ovenHow to set the oven for roasting when using the probe You can use the timer even though you cannot useInsert the probe into the meat timed oven operationsUsing the convection oven The convection oven fan shuts off when the oven door is openedConvection Bake Convection RoastAdapting Recipes… Cookware for Convection CookingPaper and Plastic Metal and GlassMulti-Shelf Baking How to Set the Oven for Convection Baking or RoastingTroubleshooting How to Set the Oven for Convection Roasting when Using the Probe Convection roasting guide MeatsBeef PorkUsing the timed features for convection baking Using the timed features for convection baking Press the CLEAR/OFF pad to clear the display ifTo Adjust the Thermostat Adjust the oven thermostat-Do it yourselfUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning Press the AUTO SELF CLEAN padHow to Delay the Start of Cleaning After a Clean CycleCare and cleaning of the range or any reason, be sure the anti-tip device istipping of the range and cause injury Control Panel and KnobsLift-Off Oven Door To clean the inside of the doorTo clean the outside of the door Do not lift the door by the handleOven Light Replacement Oven Heating Elementsthe main fuse or circuit breaker panel disconnect the electrical power to the range atPanel to Clean Under the Range Broiler Pan & GridHow to Remove the Storage Drawer or Kick To remove the storage drawerCooktop Surface Light Sure Grip HandleTo remove To replaceCleaning the glass cooktop Daily CleaningFor heavy, burned-on soil National Parts CenterSpecial Care Installation of the range Installation Instructions for future useBEFORE BEGINNING INSTALLATION Before You Begin1 Prepare the Opening install in either rear cornerNot less than the width 30 ″2 Prepare for Electrical Connection Flooring Under the RangeWhen moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood or similar material as follows 3 Power Cord Strain Relief Installation Connector block Neutral terminal Ground strap Power cord 4 3-Wire Power Cord InstallationDo NOT remove ground strap connection Before 5 4-Wire Power Cord InstallationAfter NOTE ALUMINUM WIRING 6 3-Wire Conduit Installationa Do not connect aluminum wire to the connector block 7 4-Wire Conduit Installation 9 Leveling the Range 8 Anti-Tip Bracket Installation10 Final Check Before you call for service… Troubleshooting TipsProblem Customer ServiceSee the Using the See the Broiling guide See the Adjust the oventhe Broiling guide See the Using the clock and timer sectionOven not clean after a clean cycleExcessive smoking Oven door willBefore you call for service… GE Electric Range Warranty Troubleshooting TipsWe Will Replace, At No Charge To You What GE Will Not CoverService Telephone Numbers In-Home Repair Service 800-GE-CARESTDD 800-TDD-GEAC Special Needs Service