GE 164D3333P033, 49-8779 manual How to Set the Oven for Cleaning, Press the AUTO SELF CLEAN pad

Page 35

How to Set the Oven for Cleaning

Never force the latch handle. Forcing the handle will damage the door lock mechanism.

How to Set the Oven for Cleaning

1 Latch the door.

				Press the AUTO SELF CLEAN pad.
			2	Press the AUTO SELF CLEAN pad.
				Using the + or – pad, enter the desired clean time.
			3	Using the + or – pad, enter the desired clean time.
		Clean cycle time is normally 3 hours. You can change
		the clean time to between 2 hours and 4 hours,
		depending on how dirty your oven is.
or		The self-clean cycle will automatically begin after CLEAN
or		The self-clean cycle will automatically begin after CLEAN

is displayed and the time for the clean cycle is set. The words ON and LOCK will appear in the display. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCK light goes off.

When the LOCK light is off, slide the latch handle to the left as far as it will go and open the door.

■The word door will be displayed, the word LOCK will flash and the oven control will signal if you set the clean cycle and forget to close the oven door.

■To stop a clean cycle, press the CLEAR/OFF pad. When the LOCK light goes off and the oven has cooled below the locking temperature, open the door.

Safety Information Operating Instructions Installation Instructions Troubleshooting Tips Customer Service

35

Image 35

Contents JBP90 JBP95 GE AppliancesGE Answer Center Owner’s Manualdrawer Staple sales slip or cancelled check hereCongratulations You Are Now Part of the GE Family Write the model and serial numbers here # #Safety Information GE & You A Service PartnershipTroubleshooting Tips If You Need ServiceWARNING ANTI-TIP DEVICE IMPORTANT SAFETY NOTICEIMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING or using a ventilation fan or hoodSafety Information Operating SAFETY PRECAUTIONSSafety Information Safety Information Operating Instructions Installation WHEN COOKING PORK…OVEN SELF-CLEANING OVEN HALOGEN/RADIANT SURFACE UNITS Instructions Safety InformationAlways turn the surface units off before removing cookware HALOGEN/RADIANT SURFACE UNITS Customer ServiceInstructions Safety Information Cleaning the glass cooktop sectionIndicator Lights Using the surface unitsSafety How to SetTemperature Limiter Instructions Operating Instructions Safety InformationDual Surface Unit Switch Differences Between Halogen and Radiant UnitsCopper Bottom Selecting types of cookwareStainless Steel AluminumCLOCK Using the oven controlsTIMER ON/OFF STOP TIMECONV. ROAST Pad Oven Control SettingsAUTO SELF CLEAN BROIL HI/LO PadOperating Instructions Using the ovenSafety Information D C B AAluminum Foil Preheating and Pan PlacementSafety Information Operating Instructions Installation Instructions How to Set the Oven for BroilingFood Broiling guideShelf First SideTo Reset the Timer Using the clock and timerInstallation To Set the TimerHow to Set an Immediate Start and Automatic Stop Using the timed baking and roasting featuresMake sure the oven clock shows the correct time of day How to Set a Delay Start and Automatic StopDo not store the probe in the oven Using the probeInstructions Safety Informationtimed oven operations How to set the oven for roasting when using the probeYou can use the timer even though you cannot use Insert the probe into the meatConvection Roast Using the convection ovenThe convection oven fan shuts off when the oven door is opened Convection BakeMetal and Glass Adapting Recipes…Cookware for Convection Cooking Paper and PlasticTroubleshooting How to Set the Oven for Convection Baking or RoastingMulti-Shelf Baking How to Set the Oven for Convection Roasting when Using the Probe Pork Convection roasting guideMeats BeefUsing the timed features for convection baking Press the CLEAR/OFF pad to clear the display if Using the timed features for convection bakingAdjust the oven thermostat-Do it yourself To Adjust the ThermostatBefore a Clean Cycle Using the self-cleaning ovenPress the AUTO SELF CLEAN pad How to Set the Oven for CleaningAfter a Clean Cycle How to Delay the Start of CleaningControl Panel and Knobs Care and cleaning of the rangeor any reason, be sure the anti-tip device is tipping of the range and cause injuryDo not lift the door by the handle Lift-Off Oven DoorTo clean the inside of the door To clean the outside of the doordisconnect the electrical power to the range at Oven Light ReplacementOven Heating Elements the main fuse or circuit breaker panelTo remove the storage drawer Panel to Clean Under the RangeBroiler Pan & Grid How to Remove the Storage Drawer or KickTo replace Cooktop Surface LightSure Grip Handle To removeNational Parts Center Cleaning the glass cooktopDaily Cleaning For heavy, burned-on soilSpecial Care Before You Begin Installation of the rangeInstallation Instructions for future use BEFORE BEGINNING INSTALLATION30 ″ 1 Prepare the Openinginstall in either rear corner Not less than the widthWhen moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood or similar material as follows Flooring Under the Range2 Prepare for Electrical Connection 3 Power Cord Strain Relief Installation Do NOT remove ground strap connection 4 3-Wire Power Cord InstallationConnector block Neutral terminal Ground strap Power cord After 5 4-Wire Power Cord InstallationBefore a Do not connect aluminum wire to the connector block 6 3-Wire Conduit InstallationNOTE ALUMINUM WIRING 7 4-Wire Conduit Installation 10 Final Check 8 Anti-Tip Bracket Installation9 Leveling the Range Customer Service Before you call for service…Troubleshooting Tips ProblemSee the Using the the Broiling guide See the Adjust the ovenSee the Broiling guide and timer section See the Using the clockOven door will Oven not cleanafter a clean cycle Excessive smokingPossible Causes What GE Will Not Cover GE Electric Range WarrantyTroubleshooting Tips We Will Replace, At No Charge To YouSpecial Needs Service Service Telephone NumbersIn-Home Repair Service 800-GE-CARES TDD 800-TDD-GEAC