GE 164D3333P034, 49-8780 manual Connector block terminal Bare wire

Page 45

7 4-Wire Conduit Installation

Remove the 3 screws from the connector block. Remove the grounding strap from the connector block middle location and the screw connecting it to the frame of the range. Insert bare wires between the connector block terminals and movable nuts. Tighten screws securely. Attach ground wire to the frame of the range.

WARNING: Connector block is approved for copper wire connection only. If aluminum wire is used, see note below.

NOTE: ALUMINUM WIRING

a Do not connect aluminum wire to connector block.

Use copper building wire rated for the correct amperage and voltage to make 3 (three) 3″ copper jumper wires. Connect wire as per Step 6 or 7 depending on number of wires.

b Splice copper wires to aluminum wiring using special connector terminals designed and UL-approved for joining copper to aluminum and follow the connector manufacturer’s recommended procedure closely.

Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes.

 

Screw

Bare wire tips

 

Connector block

 

 

 

Connector block terminal

 

Bare wire

 

Grounding

 

plate

Movable nut

Flexible cable

 

 

 

 

Bracket

Conduit

 

 

Safety Information Operating Instructions Installation Instructions Troubleshooting Tips Customer Service

45

Image 45
Contents GE Answer Center Congratulations You Are Now Part of the GE Family Staple sales slip or cancelled check hereWrite the model and serial numbers here You can find them on a label behindGE & You Service Partnership Small amount of carbon monoxide during the cleaning cycle Fiberglass insulation in self-clean ovens gives off a veryAll ranges can tip and injury could result California Safe Drinking Water and Toxic EnforcementSafety Precautions Safety Information When Cooking PORK… Oven SELF-CLEANING Oven Surface Cooking Units Radiant Surface Units Troubleshooting Tips Customer ServiceREMEMBER… Using the surface units How to SetWok Cooking Do not use the surface as a cutting board About the radiant surface units… glass cooktops onlySelecting types of cookware. glass cooktops only Clock and Timer Features Using the oven controlsUsing the self-cleaning oven section Oven Control SettingsBefore you begin… Using the ovenHow to Set the Oven for Broiling Preheating and Pan PlacementAluminum Foil HI Broil. To change from HI Broil to LO BroilComments Broiling guideUsing the clock and timer How to Set an Immediate Start Automatic Stop Using the timed baking and roasting featuresMake sure the oven clock shows the correct time of day How to Set a Delay Start and Automatic StopTo Adjust the Thermostat Adjust the oven thermostat-Do it yourselfBefore a Clean Cycle Using the self-cleaning ovenPress the Auto Self Clean pad How to Set the Oven for CleaningAfter a Clean Cycle How to Delay the Start of CleaningControl Panel and Knobs Care and cleaning of the rangePainted Surfaces Sure Grip HandleOven Shelves To clean the outside of the door To clean the inside of the doorLift-Off Oven Door Do not lift the door by the handleOven Heating Elements Oven Light ReplacementTo remove the cover Do not remove any screws to remove the coverOperating Instructions Safety Information To replace a surface unit To remove a surface unitCooktop Surface Light To removeTo replace Broiler Pan & Grid How to Remove the Storage Drawer to Clean Under the RangeTo remove the storage drawer To replace the storage drawerDaily Cleaning Cleaning the glass cooktopFor heavy, burned-on soil National Parts CenterSpecial Care Wiring must conform to National Electric Codes Installation of the rangePrepare the Opening Prepare for Electrical Connection Flooring Under the RangeStrain relief, they can be removed for better fit Power Cord Strain Relief InstallationDo not remove ground strap connection Wire Power Cord InstallationBefore After Wire Conduit Installation Connector block terminal Bare wire Anti-Tip Bracket Installation Leveling the RangeFinal Check Control signals after Before you call for service…Oven will not work Entering cook timeFood does not Broil properly At Broil Broil HI/LO padSee the Broiling guide Clock and timer Oven temperatureFood does not bake Or roast properlySelf-clean cycle Self-cleanWhen you wanted Oven will notAfter a clean cycle Oven not cleanExcessive smoking Oven door willPower outage When you wantLock light is on To cookOff and on Frequent cyclingSurface units Surface units will not Maintain a rolling boilNot functioning Surface unitsProperly Cooktop feels hotFive Years Replacement glass cooktop if it should crack due GE Electric Range WarrantyWe Will Replace, At No Charge To You What GE Will Not CoverService Telephone Numbers In-Home Repair Service 800-GE-CARESTDD 800-TDD-GEAC