Aga Ranges U110054 manual Wire Conduit Installation, Installing a 3-Wire Power Cord

Page 33

INSTALLATION

Check the appliance is electrically safe and gas sound when you have finished.

4-Wire Conduit Installation

Fig.7-18

Disconnect the supplied power cord from the terminal block

and ground post. Keep the terminal block parts; you will need them. Remove the strain relief clamp from the power cord

and remove the power cord and strain relief clamp from the mounting bracket (Fig.7-18).

The range is shipped with reducer plates to give a 11/8’’

diameter opening for conduit connection. Find the reducer0040 4 Wire Conduit Fitting plates (Fig.7-19)in the conversion kit and fix them to the

mounting bracket.

Attach a squeeze connector (not supplied with the range), to your conduit. Insert the conduit through the reducer plates on the mounting bracket. Allow enough slack to easily attach the wires to the terminal block.

Note: DO NOT install the conduit without a squeeze connector.

Fig.7-19

ArtNo.280-0039 Reducer Plate

Attach the wires to the ground post and terminal block (Fig.7-20).

Note: Make sure the wires are completely inserted into the terminals and secure connections are made.

Secure the squeeze connector in place in the bracket by tightening the squeeze connector screws.

Replace the electrical connection cover.

ArtNo.280-0081 - 4 Wire conduit terminal connection

Black

Fig.7-20

Red

Installing a 3-Wire Power Cord

Disconnect the supplied power cord from the terminal block and ground post. Keep the terminal block parts; you will need them. Remove the strain relief clamp from the power cord and remove the power cord and strain relief clamp from the mounting bracket. Discard the strain relief clamp.

Note: DO NOT install the power cord without a strain relief

– use the clamp supplied with the cord.

White

Green

Ground

Fig.7-21

Install the new strain relief device to the mounting bracket by removing the two clamping screws, feeding the two halves (ears first) through the hole in the mounting bracket and loosely replacing the screws. Insert the power cord through the strain relief device but do not tighten the device yet (Fig.7-21).

A ground strap is supplied in the conversion pack (Fig.7-22).

Attach the ground strap to the ground and center terminal of the connector block (Fig.7-23).

The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the connector block. The power leads must be connected to the outside terminals.

Make sure the connections are tight. Now tighten the strain relief device to clamp the power cord.

Refit the electrical connection cover.

ArtNo.280-0042 Ground Strap

Fig.7-22

 

Fig.7-23

BlackArtNo.280-0082 - 3-Wire conduit connection‘Ground strap’

White

 

Red

Strain relief

 

device

Ground

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents User Guide Contents Case of Fire Important Safety InformationTo Prevent Fire or Smoke Damage  Do Not Leave Children Alone or UnattendedProper Installation Important Safety Notice and WarningWear Suitable Clothing ConversionGeneral Safety Instructions Placement of Oven RacksEnamel and may be cleaned off with a metal polish Use the Right Size PanPage Range Overview 5Fig.2-6 Igniting Cooktop Burners without ElectricityMulti-function Oven Wok BurnerAFig.2-9 Function UseMulti-function oven modes -13 Operating the OvenThaw and Serve Convection OvenFan Assisted Oven Self-CleaningConventional Oven Top and Base Heat Browning ElementSabbath Mode Energy Saving Panel FeatureRemoving the Divider To set the time of day ClockTo time something that is cooking minute minder To stop the oven automaticallyKey Lock Auto is showing, you want to reset to manual cookingTo activate the key lock To turn off the key lockOven racks AccessoriesTo remove and refit the racks To remove and refit the telescopic rack and runnersStorage Oven LightTo Remove the Drawer Replace the storage drawerCooking Tips Tips on Cooking with the TimerCooking with a Multi-function Oven General Oven TipsMeat Cooking TableTroubleshooting Timed oven is not coming on when automatic cooking Oven temperature getting hotter as the range gets olderAn oven light is not working Cleaning for Spills Cleaning Your RangeEssential Information Daily CareMain Top Self-Clean OvenControl Panel and Oven Doors Removing the oven door outer panelSelf-Clean Operation Before using the self-clean function WARNING! The oven will still be hot Hours SoilingPart Finish Recommended Cleaning method Cleaning Table TableTo cancel the self cleaning cycle To start the self cleaning cycle automatically Warning Installation Safety Instructions InstallationRegulations Converting to Propane GasAdditional materials you may need You will also need the following toolsGas line shut-off valve Checking the partsPositioning the Range Removing the Oven Door Moving the RangeRemoving the Storage Drawer  The range is very heavy. Take great careInstalling the Flue Grille Completing the MoveLeveling Procedure Kit ContentsAnti-Tip Device Wall AttachmentElectrical Connection Wire Conduit Installation Installing a 3-Wire Power CordDisconnect the supplied power cord from the terminal block Black Gas Supply Requirements Gas ConnectionProvide Adequate Gas Supply CanadaFlexible Connector Connect the Range to the Gas Supply CAUTIONleaks. do not use a flame to check for gas Final Fitting Seal the OpeningsRange Operational Checks Customer CareMoving the Range for Servicing Valve Adjustment For Your SafetyConversion to Another Gas Conversion to PropaneGas Regulator For safety’s sake push the drawer rails back out of the wayReplacing the Bypass Screw TypeStick on label Pressure TestingRefitting the Flue Grille Refitting the Grille and DrawerCode Description Colour Code Circuit DiagramDimensions Technical DataConnections RatingsPage Page If further help is needed concerning this warranty, contact Consumer WarrantyArtNo.000-0003 CE logo
Top Page Image Contents