Aga Ranges U110054 manual Moving the Range, Removing the Oven Door, Removing the Storage Drawer

Page 29

INSTALLATION

Check the appliance is electrically safe and gas sound when you have finished.

Moving the Range

The range is very heavy. Take great care.

We recommend two people maneuver the range. Ensure that the floor covering is firmly attached or removed to prevent it being disturbed when moving the range around. You will need the leveling tool.

Removing the Oven Door

To remove the door, open the door fully. Swivel the locking ‘U’ clips forward to the locking position (Fig.7-3). Grip the sides of the door, lift upwards and then slide the door forwards (Fig.7-4)and remove.

Removing the Storage Drawer

Pull the drawer right out.

Push the ends of the plastic clips – down on the left-hand side, up on the right-hand side – to release the catches holding the drawer to the side rails (Fig.7-5). At the same time pull the drawer forwards and away from the side rails.

For safety’s sake push the drawer rails back out of the way.

Put the drawer somewhere safe – do not replace it until you have completed the installation, you will need access to the area behind the drawer.

When you have removed the oven door and storage drawer continue as follows:

First fit the leveling tool on the hexagonal adjusting nut (Fig.7-6).

Make 10 complete (360°) turns clockwise (Fig.7-7). (This means turning and removing the leveling tool 20 times.)

Make sure you lower BOTH REAR ROLLERS. There are two adjusting nuts, one for each roller, at both the front bottom corners of the range.

Note that the rollers are only intended to aid installation – the range should not be moved once it is installed.

Fig.7-3

Fig.7-4

ArtNo.325-0002 - BI oven removing the door

Fig.7-5

ArtNo.010-0002 Rear roller nut

Fig.7-6

 

Fig.7-7

ArtNo.010-0010 Lowering the rear rollers (90)

x10

27

Image 29
Contents User Guide Contents Case of Fire Important Safety InformationTo Prevent Fire or Smoke Damage  Do Not Leave Children Alone or UnattendedProper Installation Important Safety Notice and WarningWear Suitable Clothing ConversionGeneral Safety Instructions Placement of Oven RacksEnamel and may be cleaned off with a metal polish Use the Right Size PanPage Range Overview 5Fig.2-6 Igniting Cooktop Burners without ElectricityMulti-function Oven Wok BurnerAFig.2-9 Function UseMulti-function oven modes -13 Operating the OvenThaw and Serve Convection OvenFan Assisted Oven Self-CleaningConventional Oven Top and Base Heat Browning ElementRemoving the Divider Sabbath ModeEnergy Saving Panel Feature To set the time of day ClockTo time something that is cooking minute minder To stop the oven automaticallyKey Lock Auto is showing, you want to reset to manual cookingTo activate the key lock To turn off the key lockOven racks AccessoriesTo remove and refit the racks To remove and refit the telescopic rack and runnersStorage Oven LightTo Remove the Drawer Replace the storage drawerCooking Tips Tips on Cooking with the TimerCooking with a Multi-function Oven General Oven TipsMeat Cooking TableTroubleshooting An oven light is not working Timed oven is not coming on when automatic cookingOven temperature getting hotter as the range gets older Cleaning for Spills Cleaning Your RangeEssential Information Daily CareMain Top Self-Clean OvenControl Panel and Oven Doors Removing the oven door outer panelSelf-Clean Operation Before using the self-clean function WARNING! The oven will still be hot Hours SoilingPart Finish Recommended Cleaning method Cleaning Table TableTo cancel the self cleaning cycle To start the self cleaning cycle automatically Warning Installation Safety Instructions InstallationRegulations Converting to Propane GasAdditional materials you may need You will also need the following toolsGas line shut-off valve Checking the partsPositioning the Range Removing the Oven Door Moving the RangeRemoving the Storage Drawer  The range is very heavy. Take great careLeveling Installing the Flue GrilleCompleting the Move Procedure Kit ContentsAnti-Tip Device Wall AttachmentElectrical Connection Disconnect the supplied power cord from the terminal block Wire Conduit InstallationInstalling a 3-Wire Power Cord Black Gas Supply Requirements Gas ConnectionProvide Adequate Gas Supply Canada CAUTIONleaks. do not use a flame to check for gas Flexible ConnectorConnect the Range to the Gas Supply Final Fitting Seal the OpeningsMoving the Range for Servicing Range Operational ChecksCustomer Care Valve Adjustment For Your SafetyConversion to Another Gas Conversion to PropaneGas Regulator For safety’s sake push the drawer rails back out of the wayReplacing the Bypass Screw TypeStick on label Pressure TestingRefitting the Flue Grille Refitting the Grille and DrawerCode Description Colour Code Circuit DiagramDimensions Technical DataConnections RatingsPage Page If further help is needed concerning this warranty, contact Consumer WarrantyArtNo.000-0003 CE logo