IDEAL INDUSTRIES BUC5034 manual Servicing Maintenance and Periodic Checks

Page 21

SERVICING

6.

MAINTENANCE AND PERIODIC CHECKS

Magnesium anode

Safety valve or group

 

 

The magnesium anode must be checked at least every two years.

 

 

 

 

Starting with the first check and taking account of the wear to the

 

WARNING

 

 

anode, the frequency of the following checks must be decided. The

 

 

 

anode can be checked according to one of the following two

 

IMPORTANT: The safety unit must be used

 

methods:

 

periodically (at least once per month). To do

 

-

Visual check:

 

this, place the safety group in the draining position.

 

 

The anode must be replaced if its diameter is less than 15mm

 

This allows the evacuation of any deposits which

 

 

 

 

 

(initial diameter = 33mm)

 

could eventually obstruct the safety group valve.

 

 

 

 

-

Check by measurement:

 

Non-compliance with this requirement could

 

 

result in a deterioration of the unit's tank (see

 

 

- Disconnect the earth wire to the anode.

 

notice enclosed with the safety unit).

 

 

 

- Measure the current between the tank and the anode; if

 

 

 

 

 

 

 

 

 

the current is less than 0.1 mA, the anode must be

De-scaling:

 

 

 

replaced.

 

in hard water regions, it is advisable to ask the installer to

The outside of the unit can be cleaned with soapy water.

 

carry out an annual de-scaling of the tank exchanger so that

Replace the inspection cover taking care to place the salt

 

it will retain its performance.

 

 

Operations to be carried out during the de-scaling, visual checks

 

rod at the bottom and refit the washer:

 

- position the lip seal in the inspection hole, being careful

and replacement of the magnesium anode.

 

 

 

Shut off the cold water supply and drain the tank. To drain it

 

to place its tongue outside the tank.

 

- position the retaining ring around the seal, placing the

 

via the safety unit, put the latter into the drainage position

 

 

and open a hot water tap so that air can enter.

 

 

 

tongue above the ring.

Take off the front panel and the probes.

 

 

 

- Refit the cover, salt rod at the bottom, on the flange,

 

 

 

 

tightening the 6 bolts evenly across the diameter of the

Take off the cover (13 mm spanner).

 

 

 

cover.

If necessary, replace the anode.

 

 

 

 

Remove all the scaling deposits from the bottom of the tank.

 

 

 

The exchanger must be de-scaled in order to guarantee its

 

￿￿￿￿￿￿￿￿￿￿￿￿￿￿

 

￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿

 

 

proper operation.

 

 

 

 

￿￿￿￿￿￿￿

Buccaneer GT, Falcon GTE - Installation, Assembly & Servicing

21

Image 21
Contents Installation, Assembly and Servicing General Technical Specifications of Combination Boilers Main Dimensions Buccaneer GT Combination Boiler Falcon GTE Combination BoilerHreaded Assembly Installation Installing the BoilerBoiler Location VentilationInstallation Hydraulic ConnectionsConnection of the Domestic Hot Water Circuit Example Buccaneer GT Example of InstallationTools required Assembly Buccaneer GT Combination BoilerAssembly Package IC1, IC2, IC3Assembling the base and draining tube Assembling the boiler onto the tank Installing the pipes Assembling the tank front panelBoiler GTE 4 GTE 5 Assembly Falcon GTE Combination BoilerInstalling the tubes Assemble the boiler as instructed in figures 1Assembling the boiler on the hot water tank Hydraulic Boiler to Tank Connections Kit BH46 AssemblyAssembly Controls DescriptionOperating Principle Electrical Connections Fitting and Connecting the MB1 ModuleMB1 Domestic Hot Water Sensor Operating and Installation Package AD127Tank Sensor Boiler SensorAdjusting the limiter thermostat Adjusting the timing of the charging pumpInstallation and Connection Instructions for useSecuring the module Connections Installation with MB1 ModuleHeating and Domestic Hot Water Installation with MB1 module Connecting the BurnerAssembly Commissioning Starting UpCommissioning Secondary Circuit Servicing Maintenance and Periodic Checks Buccaneer GT, Falcon GTE Installation, Assembly & Servicing Buccaneer GT, Falcon GTE Installation, Assembly & Servicing Ideal Installer/Technical Helpline 01482 498