Brinkmann Gourmet 4 Filling the LP GAS Cylinder, Installing the LP GAS Cylinder Onto the Grill

Page 7

WARNING

FILLING THE LP GAS CYLINDER:

•Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder.

•New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank.

•DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or flame an explosion causing severe burns, bodily harm, or death could occur.

•Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve, other types of caps or plugs may result in leakage of propane.

•If you exchange a cylinder with a qualified exchange program, be sure the cylinder has a Type 1 valve and an over-filling prevention device (OPD).

INSTALLING THE LP GAS CYLINDER ONTO THE GRILL:

1.Check that the cylinder valve is closed by turning the knob clockwise.

2.Open the right side door of your grill cabinet. Place the cylinder into the tank holder in the bottom of cabinet.

3.Orient the cylinder such that the valve opening faces the side burner, and so that the hose is not kinked or damaged.

4.Fully tighten the tank retention screw on the back side of grill to secure tank.

5.Attach or detach regulator to the LP gas cylinder only when cylinder is at rest in tank holder.

HOSE AND REGULATOR:

Your grill is equipped with a Type 1 connection device with the following features:

1.The system will not allow gas flow from the cylinder until a positive connection to the valve has been made.

Note: The cylinder valve must be turned off before any connection is made or removed.

2.A thermal device that will shut off the gas flow if the device is subject to temperatures above 240°F to 300°F (115°C to 150°C). If this should happen, remove the entire regulator assembly and dispose of properly. A replacement regulator assembly can be purchased by contacting customer service at 800-527-0717. The cause of the excessive heat should be determined and corrected before using your grill again.

3.A regulator flow limiting device, when activated, restricts the flow of gas to 10 cubic feet per hour. If the flow limiting device is activated, perform Regulator Resetting Procedure.

Tank Retention Screw

REGULATOR RESETTING PROCEDURE:

1.Make sure that all burners are off. The red indicator light above the ON/OFF switch for the burners should not be lit, turn off the cylinder valve and disconnect regulator from LP gas tank. Wait approximately two minutes.

2.Reattach regulator and slowly turn cylinder valve back on. The flow limiting device will now be reset.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Aviso Para EL Instalador Important Safety Table of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Hose and Regulator Installing the LP GAS Cylinder Onto the GrillRegulator Resetting Procedure Filling the LP GAS CylinderConnecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderWhen to Perform a Leak Test Leak TestingChecking for Leaks PRE-START Check List Lighting Main and Side Burner Lighting InstructionsMatch Lighting Main and Side Burner Preheating the Grill Turning OFF the GrillOperating the Grill Breaking in Your GrillSide Burner Using the BUILT-IN Electrical OutletsConvection Oven Helpful Hints CleanlinessGrilling to Proper Temperature Grill Cooking TipsCleaning and Maintenance Proper Care & MaintenanceCooking Grills Burner ASSEMBLY/MAINTENANCEHeat Distribution Plates Before Storing Your Grill Transporting and StorageTrouble Shooting Question Why does my grill not light properly? Frequently Asked QuestionsFrequently Asked Questions Assembly Instructions Page Step Step Charmglow 8640 Assembled Part Description Replacement Parts ListPCB Advertencias Índice DE Materias Advertencias Generales Cilindro DE GAS LP no Incluido CON Esta Parrilla Información Sobre LA InstalaciónEspecificaciones DEL Cilindro Método Para Restablecer EL Regulador Cómo Llenar EL Cilindro DE GAS LPCómo Instalar EL Cilindro DE GAS LP a LA Parrilla Manguera Y ReguladorCómo Conectar LA Manguera Y EL Regulador Cuándo Realizar UNA Prueba DE Detección DE Fugas Prueba DE Detección DE FugasCómo Revisar Para Encontrar Fugas Lista DE Revisión Antes DEL Primer USO Cómo Encender EL Quemador Principal Cómo Precalentar LA Parrilla Cómo Apagar LA ParrillaCómo Utilizar LA Parrilla Cómo Estrenar SU ParrillaCómo Utilizar LOS Tomacorrientes Integrados EL Quemador LateralEL Horno DE Convección Cómo Asar a LA Parrilla a LA Temperatura Indicada LimpiezaConsejos Útiles Limpieza Y Mantenimiento Debido Cuidado Y MantenimientoParrillas Para Cocinar Ensamblado Y Mantenimiento DEL QuemadorPlacas DE Distribución Térmica Antes DE Guardar SU Parrilla Transporte Y AlmacenamientoProblema Posibles causas Resolución DE ProblemasPregunta ¿Por qué no se enciende bien mi parrilla? LAS Preguntas MÁS FrecuentesLAS Preguntas MÁS Frecuentes Instrucciones DE Ensamblado Page Paso Emparrillado Del Quemador Lateral Charmglow 8640 Armada No. De La Descripción Parte De la Parte Lista DE Piezas DEL Reemplazo8640-28 Dispositivo De La Ignición 8640-29 Warranty
Top Page Image Contents