Brinkmann Gourmet 4 Burner ASSEMBLY/MAINTENANCE, Cooking Grills, Heat Distribution Plates

Page 17

BURNER ASSEMBLY/MAINTENANCE

Although your burners are constructed of stainless steel, they may corrode as a result of the extreme heat and acids from cooking foods or from the climate your grill is exposed to. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage. If found, replace the burner.

DO NOT obstruct the flow of combustion and ventilation air. Burner tubes can become blocked by spiders and other insects building their nests. Blocked burner tubes can prevent gas flow to the burners and could result in a burner tube fire or fire beneath the grill. To clean the Burner Assembly follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill.

1.Make sure power to all burners are off. The red indicator light above the ON/OFF switch should not be lit. Turn gas off at the LP cylinder tank valve.

2.Remove cooking grills, and heat distribution plates.

3.Remove screws from each burner “foot” and carefully lift each burner up and away from valve openings.

4.Use a narrow bottle brush or a stiff wire bent into a small hook to run through each burner tube and flame port several times.

Note: Wear eye protection when performing procedure 5.

5.Use compressed air to blow into burner tube and out the flame ports. Check each port to make sure air comes out each hole.

6.Wire brush entire outer surface of burner to remove food residue and dirt.

7.Check burner for damage. If any large cracks or holes are found replace burner.

8.Carefully replace burners and secure with screws removed in Step 3.

Screws

Burner Orifice

Valve Tip

Burner Tube

Burner Port

To Clean Burner Tube

Insert Hook Here

IMPORTANT: Burner opening must slide over valve nozzle.

9.There are 5 viewing holes on the back panel of the grill body for inspecting and proper alignment of the main burners or side burner.

10.Follow the "Gas Leak Testing" section of this manual. Relight burners to verify proper operation.

11.Replace heat distribution plates and cooking grills.

COOKING GRILLS

Clean with mild soap detergent and water. A brass bristled brush or a nylon cleaning pad can be used to remove residue from the stainless steel surfaces. Do not use steel wire bristles to clean the cooking grills. Steel can cause the finish to chip or crack. DO NOT use a commercial oven cleaner.

HEAT DISTRIBUTION PLATES

Periodically, it may be necessary to inspect and clean the heat distribution plate to prevent excess grease build-up. When the grill is cold, remove the cooking grills. Inspect the heat distribution plates and replace if broken or damaged. Do not allow heat distribution plates to become damaged to the extent that they may fall through onto the burners. Replace the heat distribution plates and cooking grills and light the burners. Operate the grill on "HIGH" for 10 minutes to remove the excess grease.

16

Image 17
Contents Aviso Para EL Instalador Important Safety Table of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Regulator Resetting Procedure Installing the LP GAS Cylinder Onto the GrillFilling the LP GAS Cylinder Hose and RegulatorConnecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderChecking for Leaks Leak TestingWhen to Perform a Leak Test PRE-START Check List Match Lighting Main and Side Burner Lighting InstructionsLighting Main and Side Burner Operating the Grill Turning OFF the GrillBreaking in Your Grill Preheating the GrillSide Burner Using the BUILT-IN Electrical OutletsConvection Oven Grilling to Proper Temperature CleanlinessGrill Cooking Tips Helpful HintsCleaning and Maintenance Proper Care & MaintenanceHeat Distribution Plates Burner ASSEMBLY/MAINTENANCECooking Grills Before Storing Your Grill Transporting and StorageTrouble Shooting Question Why does my grill not light properly? Frequently Asked QuestionsFrequently Asked Questions Assembly Instructions Page Step Step Charmglow 8640 Assembled Part Description Replacement Parts ListPCB Advertencias Índice DE Materias Advertencias Generales Cilindro DE GAS LP no Incluido CON Esta Parrilla Información Sobre LA InstalaciónEspecificaciones DEL Cilindro Cómo Instalar EL Cilindro DE GAS LP a LA Parrilla Cómo Llenar EL Cilindro DE GAS LPManguera Y Regulador Método Para Restablecer EL ReguladorCómo Conectar LA Manguera Y EL Regulador Cómo Revisar Para Encontrar Fugas Prueba DE Detección DE FugasCuándo Realizar UNA Prueba DE Detección DE Fugas Lista DE Revisión Antes DEL Primer USO Cómo Encender EL Quemador Principal Cómo Utilizar LA Parrilla Cómo Apagar LA ParrillaCómo Estrenar SU Parrilla Cómo Precalentar LA ParrillaCómo Utilizar LOS Tomacorrientes Integrados EL Quemador LateralEL Horno DE Convección Consejos Útiles LimpiezaCómo Asar a LA Parrilla a LA Temperatura Indicada Limpieza Y Mantenimiento Debido Cuidado Y MantenimientoPlacas DE Distribución Térmica Ensamblado Y Mantenimiento DEL QuemadorParrillas Para Cocinar Antes DE Guardar SU Parrilla Transporte Y AlmacenamientoProblema Posibles causas Resolución DE ProblemasPregunta ¿Por qué no se enciende bien mi parrilla? LAS Preguntas MÁS FrecuentesLAS Preguntas MÁS Frecuentes Instrucciones DE Ensamblado Page Paso Emparrillado Del Quemador Lateral Charmglow 8640 Armada No. De La Descripción Parte De la Parte Lista DE Piezas DEL Reemplazo8640-28 Dispositivo De La Ignición 8640-29 Warranty