Sennheiser EW 300 IEM G2 manual Inserting and replacing the batteries, Connecting the headphones

Page 13

EK 300 IEM G2 stereo receiver

Inserting and replacing the batteries

For powering the EK 300 IEM G2 receiver, two 1.5 V AA size batteries are required.

Press the two unlocking buttons

and open the battery compartment

cover .

 

Insert the two batteries as shown in the diagram on the left. Please observe correct polarity when inserting the batteries.

Close the battery compartment. The battery compartment cover locks into place with an audible click.

Inserting and charging the accupack

The receiver can also be powered via the rechargeable Sennheiser BA 2015 accupack. Insert the accupack into the battery compartment as described above. The transmitter has two charging contacts and a sensing contact on its short sides. The accupack can be recharged while remaining in the transmitter. Insert the transmitter into the L 2015 charger (see operating manual of the L 2015 charger).

Note:

For accupack operation of the receiver, only use the BA 2015 accupack In order to ensure optimum operational reliability. For charging the accupack, only use the L 2015 charger. Both the accupack and the charger are available as accessories. The accupack is fitted with an integrated sensor which is – via a third contact – monitored by the electronics of the receiver and the charger. The sensor is necessary for the following control purposes:

yThe taking into account of the different voltage characteristics of pri- mary cells (batteries) and accupacks. The battery status indications on the displays, the transmission of transmitter battery status information to the rack-mount receivers and the switch-off thresholds at the end of the operating time are corrected correspondingly. Due to the missing sensor, individual rechargeable battery cells will not be identified as accupacks.

yThe monitoring of the accupack temperature during charging in the L 2015 charger.

yThe prevention of improper charging of inserted primary cells (batte- ries). Due to the missing sensor, individual rechargeable battery cells will also not be charged in the L 2015 charger.

Connecting the headphones

If you use the receiver as part of the monitoring system, connect the supplied in-ear headphones or any Sennheiser stereo headphones with 3.5 mm stereo jack plug to the headphone output (PHONES) .

Attention! High volume!

Even short exposure to high volume levels will damage your hearing! Set the volume for the connected headphones to the minimum before putting the headphones on.

First, set the volume control to the lowest volume by turning it to the left as far as possible. Then gradually turn up the volume.

Volume up? – NO!

When people use headphones, they tend to choose a higher volume than with loudspeakers. Listening at high volume levels for long periods can lead to permanent hearing defects. Please protect your hearing, Sennheiser headphones have an excellent sound quality even at low volumes.

51

Page 12 Page 14
Image 13
Page 12 Page 14
Contents W300 IEM Thank you for choosing Sennheiser Contents Channel bank system Ew 300 IEM G2 systemSystem components Safety instructionsSR 300 IEM G2 stereo transmitter Overview of operating controlsEK 300 IEM G2 stereo receiver Indications and displays on the receiver Indications and displays on the transmitterMute display RF signal indicationPilot display Display backlightingConnecting the mains unit Connecting the antennaConnecting the amplifier/mixing console Preparing the components for useVolume up? no Connecting the headphones/monitoring the audio signalService interface Rack adapter and antenna mountBNC extension cables using the supplied plain Inserting and replacing the batteries Connecting the headphonesInserting and charging the accupack Switching the components on/off Using the componentsAdjusting the volume Switching the transmitter on/offActivating/deactivating the lock mode Adjusting the balanceAttaching the receiver to clothing Buttons Operating menuWorking with the operating menu Overview of menusStoring a setting Adjusting a settingGetting into the operating menu Selecting a menu786.300 MHz 790.250 MHz Operating menu of the stereo transmitter790.250 MHz 807.900 MHz 786.300 MHz 797.075 MHzStereo IiiiiiOff MonoOperating menu of the stereo receiver ExitName PLT. on Switching between channel banks Adjustment tips for the operating menuSwitching between the channels in a channel bank Scanning the channel banks for free channels receiver onlyMulti-channel operation Adjusting the squelch threshold receiver onlyStarting the scan and storing the scan result Releasing locked channelsStereo/FOCUS selection receiver only Adjusting the sensitivity transmitter onlyIMPORTANT! Notes Entering a name Selecting the standard displaySR 300 IEM G2 stereo transmitter EK 300 IEM stereo receiverStereo/Mono selection transmitter only Loading the factory-preset default settingsExiting the operating menu ExitError checklist TroubleshootingRecommendations and tips Care and maintenanceFor the EK 300 IEM G2 receiver For optimum receptionAdditional information Wireless transmission systemsHDX noise reduction Pilot tone squelch SquelchField strength-dependent squelch IE 3 in-ear headphones SpecificationsSystem EK 300 IEM G2 stereo receiverConnector assignment AccessoriesDeutsch Italiano Sennheiser electronic GmbH & Co. KG Nota BemerkungObservación Opmerking

EW 300 IEM G2 specifications

The Sennheiser EW 300 IEM G2 is a professional in-ear monitoring system designed for musicians, sound engineers, and audio professionals seeking high-quality wireless audio performance. One of the standout features of the EW 300 IEM G2 is its robust transmission range, which allows users to enjoy reliable audio performance over distances of up to 330 feet in optimal conditions. This feature is essential for performers who require freedom of movement on stage without compromising audio quality.

The EW 300 IEM G2 employs a true diversity receiver design, which minimizes the risk of dropouts and ensures consistent audio quality. This technology utilizes two antennas that receive the same signal, selecting the stronger one to maintain a stable connection. The system operates on multiple frequency ranges, allowing users to choose the best channel that suits their needs while reducing interference from other wireless devices.

Another notable aspect is the high-quality audio output. The EW 300 IEM G2 supports a frequency response of 25 Hz to 19 kHz, ensuring a natural sound reproduction across the entire audio spectrum. This wide frequency range makes it suitable for various applications, from live performances and studio recordings to theatrical productions.

The EW 300 IEM G2 features a simple and intuitive user interface, allowing for easy setup and operation. Its LCD display provides essential information such as frequency, channel, and battery status, helping users stay informed during performances. The system also includes features like auto-scan, which identifies available frequencies and automatically selects the best one for optimal performance.

Furthermore, the EW 300 IEM G2 is versatile, accommodating various earpieces to suit individual preferences and comfort levels. Whether using custom-molded in-ear monitors or universal earbuds, the system can deliver a tailored listening experience.

Overall, the Sennheiser EW 300 IEM G2 stands out as a reliable and feature-rich in-ear monitoring solution. Its advanced technologies, user-friendly interface, and high-quality audio capabilities make it a preferred choice for professionals in the music and entertainment industry.
Top Page Image Contents