Sennheiser EW 300 IEM G2 manual Stereo/FOCUS selection receiver only, IMPORTANT! Notes

Page 26

IMPORTANT! Notes:

ST-FOC

LTD

HI-BST

Sensitiv

yIf the squelch threshold is adjusted too high, the transmission range will be reduced. Therefore, always adjust the squelch threshold to the lowest possible setting.

yWhen in the setting mode of the “SQELCH” menu, pressing the button for more than three seconds will switch the squelch off.

“SQ.OFF” appears on the display. If no RF signal is being received, his- sing noise will occur. This setting is for test purposes only.

Stereo/FOCUS selection (receiver only)

Via the “ST-FOC” menu, you can switch between stereo and FOCUS operation.

In both operating modes, the SR 300 IEM G2 stereo transmitter has to be set to stereo operation.

When the receiver is set to stereo operation, the left-right signals are available as usual.

When the receiver is set to FOCUS operation, the left-right signals are mixed and are available as a mono signal in both headphone channels. Use the / rocker button to adjust the relative levels of the two separate channels in

the mixed mono signal (see “Adjusting the balance” on page 53).

Limiting the volume at the headphone output (receiver only)

Via the “LTD” menu, you can switch the limiter on and off. With the limiter switched on, the volume at the headphone output will be reduced.

Activating/deactivating the frequency boost (receiver only)

Via the “HI-BST” menu, you can boost the AF frequency response at 10 kHz. As a result, headphones with magnetic transducers sound better.

Adjusting the sensitivity (transmitter only)

To match the transmitter to the output level of the connected unit (e.g. mixing console), you can adjust the input sensitivity in four steps of 8 dB via the “Sensitiv” menu.

The input sensitivity is adjusted too high when close talking distances, speakers with loud voices or loud music passages cause overmodulation in the transmission link. In this case, the transmitter’s “PEAK” warning will light up and the receiver’s level display for audio signal “AF” will show full deflection.

If, on the other hand, the sensitivity is adjusted too low, the transmission link will be undermodulated, which would result in a signal with high background noise.

The sensitivity is correctly adjusted when the level display for audio signal “AF” shows full deflection only during the loudest passages.

64

Page 25 Page 27
Image 26
Page 25 Page 27
Contents W300 IEM Thank you for choosing Sennheiser Contents Ew 300 IEM G2 system Channel bank systemSafety instructions System componentsOverview of operating controls SR 300 IEM G2 stereo transmitterEK 300 IEM G2 stereo receiver Indications and displays on the transmitter Indications and displays on the receiverPilot display RF signal indicationMute display Display backlightingConnecting the amplifier/mixing console Connecting the antennaConnecting the mains unit Preparing the components for useService interface Connecting the headphones/monitoring the audio signalVolume up? no Rack adapter and antenna mountBNC extension cables using the supplied plain Inserting and charging the accupack Connecting the headphonesInserting and replacing the batteries Adjusting the volume Using the componentsSwitching the components on/off Switching the transmitter on/offAttaching the receiver to clothing Adjusting the balanceActivating/deactivating the lock mode Operating menu ButtonsOverview of menus Working with the operating menuGetting into the operating menu Adjusting a settingStoring a setting Selecting a menu790.250 MHz 807.900 MHz Operating menu of the stereo transmitter786.300 MHz 790.250 MHz 786.300 MHz 797.075 MHzOff IiiiiiStereo MonoExit Operating menu of the stereo receiverName PLT. on Switching between the channels in a channel bank Adjustment tips for the operating menuSwitching between channel banks Scanning the channel banks for free channels receiver onlyStarting the scan and storing the scan result Adjusting the squelch threshold receiver onlyMulti-channel operation Releasing locked channelsIMPORTANT! Notes Adjusting the sensitivity transmitter onlyStereo/FOCUS selection receiver only SR 300 IEM G2 stereo transmitter Selecting the standard displayEntering a name EK 300 IEM stereo receiverLoading the factory-preset default settings Stereo/Mono selection transmitter onlyExit Exiting the operating menuTroubleshooting Error checklistFor the EK 300 IEM G2 receiver Care and maintenanceRecommendations and tips For optimum receptionHDX noise reduction Wireless transmission systemsAdditional information Field strength-dependent squelch SquelchPilot tone squelch System SpecificationsIE 3 in-ear headphones EK 300 IEM G2 stereo receiverAccessories Connector assignmentDeutsch Italiano Sennheiser electronic GmbH & Co. KG Observación BemerkungNota Opmerking

EW 300 IEM G2 specifications

The Sennheiser EW 300 IEM G2 is a professional in-ear monitoring system designed for musicians, sound engineers, and audio professionals seeking high-quality wireless audio performance. One of the standout features of the EW 300 IEM G2 is its robust transmission range, which allows users to enjoy reliable audio performance over distances of up to 330 feet in optimal conditions. This feature is essential for performers who require freedom of movement on stage without compromising audio quality.

The EW 300 IEM G2 employs a true diversity receiver design, which minimizes the risk of dropouts and ensures consistent audio quality. This technology utilizes two antennas that receive the same signal, selecting the stronger one to maintain a stable connection. The system operates on multiple frequency ranges, allowing users to choose the best channel that suits their needs while reducing interference from other wireless devices.

Another notable aspect is the high-quality audio output. The EW 300 IEM G2 supports a frequency response of 25 Hz to 19 kHz, ensuring a natural sound reproduction across the entire audio spectrum. This wide frequency range makes it suitable for various applications, from live performances and studio recordings to theatrical productions.

The EW 300 IEM G2 features a simple and intuitive user interface, allowing for easy setup and operation. Its LCD display provides essential information such as frequency, channel, and battery status, helping users stay informed during performances. The system also includes features like auto-scan, which identifies available frequencies and automatically selects the best one for optimal performance.

Furthermore, the EW 300 IEM G2 is versatile, accommodating various earpieces to suit individual preferences and comfort levels. Whether using custom-molded in-ear monitors or universal earbuds, the system can deliver a tailored listening experience.

Overall, the Sennheiser EW 300 IEM G2 stands out as a reliable and feature-rich in-ear monitoring solution. Its advanced technologies, user-friendly interface, and high-quality audio capabilities make it a preferred choice for professionals in the music and entertainment industry.
Top Page Image Contents