Grandstream Networks GXV300X manual Jitter Delay, No, but allow in-call enabling, Payload type

Page 38

 

Jitter Delay

 

Select desired Jitter Buffer Delay. Default is Medium. It is using 100, 200 and 400ms to

 

 

 

 

 

 

 

match the setting of low, medium and high for audio. The video always buffered and played

 

 

 

 

in synchronize with audio.

 

 

 

 

Grandstream recommends “High” for a poor network environment.

 

 

 

 

 

 

 

 

 

 

 

 

Enable Video

 

Yes: video is enabled for all calls. This is the default value.

 

 

 

 

 

 

 

No, but allow in-call enabling :

 

 

 

 

Receiving call:

 

 

 

 

There are two ways to pick up incoming video call.

 

 

 

 

-Pressing SPEAKER or picking up handset will answer the call as VOICE ONLY call.

 

 

 

 

GXV300x can still send out video request after the call is established by pressing MIR-

 

 

 

 

ROR button.

 

 

 

 

-Pressing MIRROR button will answer the call as VOICE & VIDEO call.

 

 

 

 

Making call:

 

 

 

 

-Picking up handset or pressing SPEAKER

 

 

 

 

-Pressing MIRROR button to toggle between VOICE ONLY and VOICE & VIDEO

 

 

 

 

No: video is disabled.

 

 

 

 

 

 

 

 

 

 

 

 

H.264 payload type

 

 

 

 

 

Enter a desired value (96-127) for dynamic RTP payload type of H.264 codec.

 

 

 

 

Default is 99.

 

 

 

 

 

 

 

 

 

 

 

 

H.263+ payload type

 

 

 

 

 

Enter a desired value (96-127) for payload type of H.263+ codec. Default is 103

 

 

 

 

 

 

 

 

 

 

 

 

H.263 Default Resolution

 

 

 

 

 

Default is CIF.

 

 

 

 

 

 

 

 

 

 

 

 

Enable RFC5168 Support

 

Default is No.

 

 

 

 

 

 

 

If it is set to Yes, phone will send an SIP INFO asking for update of I-frame.

 

 

 

 

 

 

 

 

 

 

 

 

SRTP Mode

 

 

 

 

 

Enable SRTP mode based on selection. Default is Disabled.

 

 

 

 

 

 

 

 

 

 

 

 

Special Feature

 

 

 

 

 

Default is Standard.

 

 

 

 

Choose the selection to meet special requirements from different Soft Switch vendors (like

 

 

 

 

Nortel, Broadsoft, Sonus, etc)

 

 

 

 

 

 

FXO SETTINGS

The FXO tab would only appear for GXV3005.

TABLE 14: FXO CONFIGURATION PAGE DEFINITIONS

Current Disconnect

This is a preconfigured value of duration for a line power drop used by specific service pro- viders. For example, for a configured value of 500ms the device will ignore any random voltage drops on the line if duration of such drop is less than 500ms and the call will NOT be considered as terminated. This is useful to prevent unnecessary call drops in some low quality PSTN lines.

Enable Tone Disconnect

Default is Yes. If set to Yes, busy tone is used as disconnect signal.

Grandstream Networks, Inc.

GXV300x User Manual

Page 36 of 54

 

Firmware 1.2.3.7

Updated: 12/2010

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Grandstream Networks, Inc Table of Contents GXV300X WEB GUI Welcome Installation 10/100Mbps RJ-45 port for connecting PC as switch mode 10/100Mbps RJ-45 port for uplink to EthernetTab with exten Sion down Handset Rest TabSion up Network Interfaces Feature RichOpen Standards Compatible Superb Audio QualityAudio Features Feature KeysVideo Features Call Handling FeaturesCaller ID Privacy Firmware UpgradesFeatures Advanced ServerUsing GXV300X IP Video Phone OSD/Camera Loopback Dis- play On/Off key UP ↑ Play and OSD ON/OFFHandset, Speakerphone and Headset Mode Completing CallsMaking Calls using IP Addresses Quick IP Call Mode For exampleCall Transfer Receiving CallsCall Waiting/ Call Hold Way ConferencingDo Not Disturb Voice Messages Message Waiting IndicatorMute/Delete Camera BlockMaking/Receiving Calls via Pstn only applicable on GXV3005 Camera Local Loopback Display and OSD ON/OFFOSD Display Explanation Making callsDisable Call Waiting per Call Disable Call Waiting for all subsequent callsEnable Call Waiting for all subsequent calls Enable Call Waiting per CallConfiguration Guide Flow Chart of KEY PAD Configuration Menu ∙ Ring Volume ∙ Audio ∙ Video Codecs ∙ Upgrade∙ Factory Reset Phone Book Call HistoryAccess the Web Configuration Pages ∙ Pstn Loopback ∙ Ethernet LoopbackDefinitions Password Sensitive with a maximum length of 25 characters Port End UserRule Syntax Time ZoneDaylight Savings Time 7,2,011,1,7,2,060Advanced User Configuration Silence Admin PasswordG723 rate SuppressionTimeout Mode Enable VideoPassword Video FrameUpgrade ConfigConfig File Use Random PortScreen Saver AuthenticateConf File DownloadCall-Waiting Tone Disable DisableCall-Waiting Disable UpdateUnregister on Reboot Authenticate IDAuthenticate Password Account ActiveSubscribe for MWI Keep-Alive Using SIP OPNAT Traversal Stun Proxy-RequireDial Plan Dial Plan Rules Enable Call FeaturesCaller Request Timer 1900x. =16172-9xxxxxx 12-9xx2-9xxxxxx 0112-9xEnable 100rel Callee Request TimerForce Timer UAC Specify RefresherEnable RFC5168 Support Jitter DelayDefault Resolution Srtp ModeAnce Silence TimeoutAC Termination Imped Caller ID SchemeEnable FXS Call Waiting Volume AmplificationDisable FXS Caller ID Caller IDConfiguration Through Secure Central Provisioning Server No Local HTTP/TFTP Server Web Configuration InterfaceKey Pad Menu Instructions for firmware upgrade via a Local Tftp Server Managing Firmware and Configuration File Download How It Works and Configuration IntroductionXML Syntax Example Phonebook FileScreensaver Images Screenshot of Screensaver Utility Ringtone File Size Connect the GXV300X to Your TV using RCA Cable USB 2.0 PortHeadset Jack Diagram Cross Over Cable For Some Model of HeadsetCross Over Cable required for Plantronics Headset PC side Monitor Device LimitationsScreenshot Monitoring Station Grandstream Networks, Inc Restore Factory Default Setting
Top Page Image Contents