Kenmore 970-5984 manual Changing oven temperature display, Setting Oven Lockout

Page 13

Setting Oven Controls

Changing oven temperature display

The oven control is preset to display °F (Fahrenheit) when shipped from the factory. The control can be changed to display either Fahrenheit or Celsius.

Example; to change the temperature to display °C (Celsius) or °F (Fahrenheit):

1.Press and hold Broil key pad for 6 seconds.

2.Press Flex Clean key pad to toggle between Fahrenheit or Celsius temperature display modes (Figs. ] & 2).

3.Press STARTtO accept choice.

Important note:

The oven temperature display cannot be modified if Bake or Flex Clean is active.

Setting Oven Lockout

LOCKOUTOVEN

The control may be programmed to lock the oven door and lock the oven control key pads.

To activate the oven lockout feature:

]. Be sure oven door is completely closed.

[]

. Press and hold STOPfor 3 seconds. DOOR LOCKED (See

Fig. 5) will appear in the display. The motor driven door latch mechanism will begin locking the oven door

automatically. Do not open the oven door. Allow about ]5 seconds for the oven door to completely lock. Once the oven door is locked, the Loc will appear in the display (See Fig. 6).

Fig. ]

Fig. 2

Setting silent or audible control mode

Silent mode allows the oven control to operate without audible tones. The control may be programmed for silent operation and later returned to operating with aM1the normaM audible tones.

Example; to set for silent or audible mode:

]. Press and hold Delay Start key pad for 6 seconds.

2.Press Flex Clean key pad to toggle between beep ON (Fig. 3) or beep OFF (Fig. 4).

3.Press STARTtO accept choice.

Fig. 3

Fig. 4

Fig. 5

Fig. 6

To cancel the oven lockout feature:

1. Press and hold STOPfor 3 seconds. The motor driven

door latch mechanism will begin unlocking the oven

door automatically. Do not open the oven door. Allow about 15 seconds for the oven door to completely unlock.

2.When the Loc and DOOR LOCKED messages no longer display, the oven door may be opened and the oven control key pads will be available for use.

Important notes:

"To avoid possible damage to the oven door latching mechanism, do not attempt to open or close the oven door whenever the DOOR LOCKED message is flashing.

If a control key pad is pressed when OVEN LOCI(OUT is active, the control may triple beep indicating the key pad action is not available when the OVEN LOCI(OUT feature is active.

]3

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Ienmore Contents Ienrnore Limited WarrantySave these instructions for future reference Install anti-tip device packed withSave these instructions for future reference Irnportant Safety InstructionsProtective Liners = do not USE IgniteSave these instructions for future reference Rnportant Safety InstructionsProduct Record Serial Plate Location 970Removing, replacing and arranging racks Before Setting Oven ContrdsTypes of oven racks Air circulation in the ovenControls Using Proper CookwareSurface MaterialElernent On indicator lights Before Setting Surface ControlsAbout the surface elements Home CanningSurface element settings Setting Surface ControlsOven Control Functions Control settingsOven control keypads Minimum & maximumSetting Timer Setting Oven ControlsSetting Clock Setting 12 or 24 hour display modeSetting Oven Lockout Changing oven temperature displaySetting silent or audible control mode To cancel the oven lockout featureSetting Bake Setting PreheatExample set oven for Preheat to 450F Setting Delay Start Setting Cook TimeWhen the programmed cook time runs out Suggestions for Convection baking Cony Bake some models Convection Bake some modelsInside Cony Roast some modelsBroil Setting Oven ControkSlow Cook Recipe Recall Warm & Hold TMRecipe Recaff cantd Adjusting Oven TemperatureOperating oven light Electrical outlet and circuit protectionSabbath Feature for use on the Jewish Sabbath & Holidays Press Stop Read before starting Flex Clean Flex CleanSelling Flex Clean Example to set Flex Clean to start immediatelyWhen Flex Clean is finished Delayed Start Flex CleanIf it becomes necessary to stop Flex Clean when active Care Cleaning General cleaning Care & CleaningAluminum foil and utensils Surface elements and drip bowls Cleaning drip bowlsTo remove the surface elements and drip bowls Never immerse a surface element in waterRaising and lowering the cooktop some models WireReplacing oven light some models Electrical outlet and circuit protection On some modelsSpecial door care instructions Removing and replacing the lift-off oven doorTo remove oven door Problem Solution Before You Call . Solutions to common problemsIf you Is tooProblem Before You Call * Solutions to common problemsProblemSolution Page Protection Agreements
Top Page Image Contents