Kenmore 970-5984 manual Before You Call * Solutions to common problems, Problem

Page 32

Before You Call * Solutions to common problems

Problem

Oven smokes excessively when broiling.

Flames inside oven or smoking from oven vent.

Oven control panel beeps & displays any F code error,

Flex Clean does not work.

Soil not completely removed after Flex Clean.

Solution

"Incorrect setting. Follow broiling instructions in Setting Oven Controls section.

"Be sure oven door is opened to broil stop position when broiling.

"Meat too close to the broil element. Reposition the broil rack to provide proper clearance between the meat & the element. Preheat the broil element for searing.

"Meat not properly prepared. Remove excess fat from meat. Cut remaining fatty edges to prevent curling, but do not cut into lean.

*Grease has built up on oven surfaces. Regular cleaning is necessary when broiling frequently. Old grease or food spatters cause excessive smoking.

*Excessive spillovers in oven. For example this will happen for pie spillovers or large amounts of grease left on the oven bottom. Wipe up excessive spillovers before starting oven. If flames or excessive smoke are present follow broiling instructions in Setting Oven Controls section.

[]

"Oven control has detected a fault or error condition. Press STOPkey pad to clear the error code. Try Bake or Broil function. If the F code error repeats, remove power from appliance, wait 5 minutes and then repower appliance and set clock with the correct time of day. Try Bake or Broil function again.

If the fault recurs, press sToPto clear and call 1-800-4-MY-HOME® for assistance (See back cover).

* Oven control not set properly. Review instructions in Flex Clean section.

"Flex Clean was interrupted. Review instructions in Flex Clean section.

"Excessive spillovers on oven bottom. Remove before starting Flex Clean.

"Failure to clean soil from the oven frame, the door liner outside the oven door gasket and the small area at the front center of the oven bottom. These areas are not in the self-cleaning area, but get hot enough to burn on residue. Clean these areas before the self-cleaning cycle is started. Burned-on residue can be cleaned with a stiff nylon brush and water or a nylon scrubber. Be careful not to damage the oven gasket.

Oven racks discolored.

Oven racks left in oven cavity during Flex Clean. Always remove oven racks

 

from oven cavity before starting a self-clean cycle. Clean by using a mild,

 

abrasive cleaner following manufacturer's instructions. Rinse with clean

 

water, dry and replace in oven.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Ienmore Ienrnore Limited Warranty ContentsInstall anti-tip device packed with Save these instructions for future referenceIrnportant Safety Instructions Save these instructions for future referenceProtective Liners = do not USE IgniteSave these instructions for future reference Safety Instructions RnportantProduct Record Serial Plate Location 970Before Setting Oven Contrds Removing, replacing and arranging racksTypes of oven racks Air circulation in the ovenUsing Proper Cookware ControlsSurface MaterialBefore Setting Surface Controls Elernent On indicator lightsAbout the surface elements Home CanningSetting Surface Controls Surface element settingsControl settings Oven Control FunctionsOven control keypads Minimum & maximumSetting Oven Controls Setting TimerSetting Clock Setting 12 or 24 hour display modeChanging oven temperature display Setting Oven LockoutSetting silent or audible control mode To cancel the oven lockout featureExample set oven for Preheat to 450F Setting PreheatSetting Bake When the programmed cook time runs out Setting Cook TimeSetting Delay Start Cony Bake some models Convection Bake some models Suggestions for Convection bakingCony Roast some models InsideSetting Oven Controk BroilSlow Cook Warm & Hold TM Recipe RecallAdjusting Oven Temperature Recipe Recaff cantdOperating oven light Electrical outlet and circuit protectionSabbath Feature for use on the Jewish Sabbath & Holidays Press Stop Flex Clean Read before starting Flex CleanSelling Flex Clean Example to set Flex Clean to start immediatelyIf it becomes necessary to stop Flex Clean when active Delayed Start Flex CleanWhen Flex Clean is finished Care Cleaning Aluminum foil and utensils Care & CleaningGeneral cleaning Cleaning drip bowls Surface elements and drip bowlsTo remove the surface elements and drip bowls Never immerse a surface element in waterWire Raising and lowering the cooktop some modelsReplacing oven light some models Electrical outlet and circuit protection On some modelsTo remove oven door Removing and replacing the lift-off oven doorSpecial door care instructions Before You Call . Solutions to common problems Problem SolutionIf you Is tooBefore You Call * Solutions to common problems ProblemProblemSolution Page Protection Agreements
Top Page Image Contents