Kenmore 790.9631, 790.9622, 790.9621, 790.9623, 790.9641 manual Setting Warmer Drawer Controls contd

Page 18

Setting Warmer Drawer Controls (cont'd)

Warmer Drawer Recommended

Food Settings Table

Food Item

Setting

Bacon

HI

Hamburger Patties

HI

Poultry

HI

Pork Chops

HI

Fried Foods

HI

Pizza

HI

Gravies

MED

Casseroles

MED

Eggs

MED

Roasts (Beef, Pork, Lamb)

MED

Vegetables

MED

Biscuits

MED

Rolls, hard

MED

Pastries

MED

Rolls (soft)

LO

Empty Dinner Plates

LO

To Set the Warmer (Warm & Ready TM) Drawer Thermostat Control (some models)

The thermostat control is used to select the temperature of the warmer drawer. It is located on the control panel (See Fig. 3 on previous page). To set the thermostat, push in and turn the knob to the desired setting. The temperatures are approximate, and are designated by HI, MED and LO.

1.Turn the knob to select the desired temperature setting.

2.For best results, preheat the drawer before adding food. An empty drawer will preheat in approximately 15 minutes.

3.Turn the thermostat control to OFF after use.

Warmer (Warm & Ready TM) Drawer Temperature Selection

(some models)

Refer to the table in the side column for recommended settings. If a particular

food is not listed, start with the medium setting. If more crispness is desired, remove the lid or aluminum foil.

Most foods can be kept at serving temperatures by using the medium setting.

When a combination of foods are to be kept warm (for instance, a meat with 2 vegetables and rolls), use the high setting.

Refrain from opening the warmer drawer while in use to eliminate loss of heat from the drawer.

Pull up with finger

Left Glide

Warmer (Warm & Ready TM) Drawer Indicator Light (some models)

The indicator light is located above the Warmer Drawer thermostat control. It turns on when the control is set, and stays on until the control is turned OFF. The warmer drawer is inoperable during the Self-Clean cycle. The indicator light will not come on during the Self-Clean cycle.

To Remove and Replace Warmer (Warm & Ready TM) Drawer

(some models)

To Remove Warmer Drawer:

Remove shield on righ glide, Pull up on left lever while pushing down on right lever.

Push down with finger

1. _

Turn power OFF before removing thewarmer drawer.

2.Open the drawer to the fully opened position.

3.On the right glide you will find a shield attached with a hex-head screw (see figure 1). Using a 1/4" socket and ratchet remove the shield.

4.Locate glide lever on each side of drawer, pull up on the left glide lever and push down on the right glide lever.

5.Pull the drawer away from the range.

Fig. 1

Fig. 2

NOTE: The warmer drawer will NOT

operatewhile in the Self-Clean and '!Oven lockout" modes

To Replace Warmer Drawer:

1.Replace shield on the right glide of the drawer body.

2.Pull the bearing glides to the front of the chassis glide (see figure 2).

3.Align the glide on each side of the drawer with the glide slots on the range.

4.Push the drawer into the range until levers "click" (approximately 2"). Pull the drawer open again to seat bearing glides into position. If you do not hear the levers "click" or the bearing glides do not feel seated remove the drawer and repeat steps 2-4. This will minimize possible damage to the bearing glides.

Electrical Shock Hazard can occur and result in

serious injury or death. Disconnect appliance from electric power before cleaning and servicing the warmer drawer.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Electric Range Estufa elctrica Table of Contents Product Record Important Safety Instructions IMPORTANT--Do not attempt to operate the range duringImportant Safety Notice Use Care When Opening Oven Door or Warmer Drawer ifUtensil Handles Should Be Turned Inward and Not Extend Over Canada Range Features Your Electric Range Features IncludeRemoving & Replacing Oven Racks Before Setting Oven ControlsOven Vent Location Arranging Oven RacksAbout the Ceramic Glass Cooktop Before Setting Oven Controls contdElement on and Hot Surface Indicator Lights About the Radiant Surface ElementsSetting Surface Controls To Operate Single Radiant Surface Elements all modelsTo Operate Simmer Select Surface Element some models Recommended Food Settings Heating Level Setting Surface Controls contdSetting the Warmer Warm & Ready TM Zone some models To Operate Dual Radiant Surface Element some modelsUsing proper cookware To Set the Cooktop Lockout Feature some models / CooktopUsing Power Element some models Surface CookingFor a silent control panel Temperature conversionOven Control Functions PAD-- UsedTo Change the Minute Timer while it is in use Setting Oven ControlsTo Set the Minute Timer To Set the ClockTo Set Control for Continuous Bake or 12 Hour Energy Saving Setting Oven Controls contdTo Set or Change the Temperature for Baking To Set Control for Oven Lockout LockoutTo Set the Timed Bake and Delay Start Features When the Set Bake Time Runs OutTo Set for Broiling To Operate the Oven LightFood category To set Warm & Hold Setting Warmer Drawer ControlsSetting the Warm & Hold TM Feature To set Warm & Hold to turn on automaticallySetting Warmer Drawer Controls contd Warmer Warm & Ready TM Drawer Indicator Light some modelsTo Remove and Replace Warmer Warm & Ready TM Drawer Self-Cleaning Self-Cleaning OvenAdhere to the following cleaning precautions Self-Cleaning contd Stopping or Interrupting a Select Self-Cleaning CycleSurfaces How to Clean Aluminum Trim Pieces & VinylTrim For light to moderate soil General Care & Cleaning contdPlastic or foods with a high sugar content For heavy, burned on soilSpecial Caution for Aluminum Use on the Ceramic Cooktop To Replace Oven DoorDoor Hinge locations With oven door Fully open Changing the Oven Light Adjusting the Oven TemperatureCare and Cleaning of Stainless Steel some models To replace the oven light bulbBefore You Call RangeEntire Appliance Does Not operate Cooktop Oven light does not workMetal OnlyPage Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only
Top Page Image Contents