Craftsman 917.272051 owner manual To Level Mower Housing, On level ground or driveway. Make sure

Page 22

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked

on level ground or driveway. Make sure

tires are propedy inflated (See "PROD- UCT SPECIFICATIONS" section of this

manual), if tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one sideof mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side. NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjust- ing.

Bottom Edgeof

Bottom Edge of

Mower to Ground

Mower to Ground

\

/

(_) Suspension

Arm

JLiftLink

ustrnent

Nut

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to-

side.If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links.

Tighten nut "E" on both front links an equal number of turns.

•When distance "D" is 1/8" to 1)2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

BOTH FRONT LINKS MUST BE EQUAL

IN LENGTH

Front Trunnion

Links

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Icraftsmanj Limited Twoyear Warranty on Craftsman Riding Equipment Parts Limited 90 DAY Warranty on BatteryWhile on the slope Follow the manufacturers recommen Serious injury or deathGeneral Operation Do notHi. Children IV. ServiceAdjust and service as required Responsible adultSafety is Involved Repair Agreement Product SpecificationsPark Plug Customer ResponsibilitiesSteering Howto SET Upyourtractor Check Battery Tools Required for AssemblyRemove all accessible loose parts Before Removingtractor from Skid Attach Steering WheelTo Drivetractor OFF Skid Install SeatAdjust seat before tightening adjustment knob Operation section for location al function of controlsInstall Mulcher Plate R N H L Knowyourtractor Your Tractor Engine Howto Useyourtractor To SET Parking BrakeStopping To USE Throttle ControlTo Operate Mower To Adjust Gauge WheelsGauge Wheel To Stop Mower BladesADD Gasoline Towing Carts and Other AttachmentsBefore Startingthe Engine Check Engine OIL Level To Start EngineMower should be properly leveled for MowingtipsMulching Mowingtips General Recommendations Maintenance ScheduleLubrication Chart Before Each USETractor Belts Clean AIR ScreenClean AIR INTAKE/COOLING Areas Transaxle CoolingSpark Plugs AIR FilterMuffler Engine OIL FilterTo Remove Mower CleaningTo Install Mower Raise attachment lift lever to its highest positionOn level ground or driveway. Make sure To Level Mower HousingFRONT-TO-BACK Adjustment JLiftLink Ustrnent NutTo Replace Mower Blade Drive Belt Belt InstallationTo Adjust Brake Belt RemovalTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak BatteryTransaxle Gear Shift Lever Neutral Adjustment Front Wheel TOE-INJCAMBERTo Replace Headlight Bulb Replacing BatteryTo Remove Hood and Grill Assembly Interlocks and RelaysCable To Adjust CarburetorAdjusting BracketEngineoil BatferyEngine Fuel System CylindersProblem Troubleshooting ChartCause Correction Troubleshooting Chart Problem Cause Troubleshooting Chart Problemcause CorrectionSchematic Tractor - Model NumberElectrical KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917.272051 Chassis and Enclosures Tractor - Model Number Chassis and Enclosures KEY Part DescriptionTractor - Model Number Ground Drive KEY Part DescriptionTractor - Model Number 917.272051 Steering Assembly TRACTOR- Model Number Steering Assembly KEY Part DescriptionTRACTOR-- Model Number Spark ArresterTRACTOR- Model Number Seat Assembly Decals Wheels &TIRESTRACTOR- Model Number Lift Assembly +-j,j+,. l Tractor - Model Number Mower DeckNots Allcomponent dimensions givenin U.S. inches Peerless Transaxle - Model Number 206-545C 778345 @/---L Valve, exhaust Std Blower Housing and Baffles l Not Illustrated Blower Housing & Baffles KEY Part DescriptionIGNITION/ELECTRICAL KEY Part Description AIR INTAKE/FILTRATION KEY Part Description20\ OIL PAN/LUBRICATION KEY Part Description Starting System KEY Part DescriptionEngine Controls KEY Exhaust J Fuel System KEY Part Description Exhaust KEY Part DescriptionPage Page Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillGet it fixed, at your home or ours

917.272051 specifications

The Craftsman 917.272051 is a robust and versatile lawn tractor designed to meet the diverse needs of homeowners and landscape enthusiasts. With its powerful engine and user-friendly features, this model stands out in its class, providing a reliable solution for maintaining a pristine lawn.

One of the standout features of the Craftsman 917.272051 is its impressive 20 HP Briggs & Stratton engine. This air-cooled, single-cylinder engine is designed to deliver robust performance, making it easy to tackle a variety of mowing tasks. The engine's reliable starting system ensures minimal downtime, allowing users to efficiently manage their mowing schedule.

The cutting deck of the 917.272051 is another highlight, measuring 42 inches in width. This size strikes a balance between maneuverability and efficiency, enabling users to navigate tight spaces while still covering a generous amount of terrain in one pass. The deck also features a deck wash system, allowing for easy cleaning and maintenance after use, which helps extend its lifespan and maintain optimal performance.

Equipped with a 6-speed transmission, the Craftsman 917.272051 offers users the flexibility to choose the appropriate speed for various mowing conditions. This feature enhances control and allows for a smoother cutting experience, whether tackling overgrown grass or maintaining a manicured lawn.

Another significant aspect of the Craftsman 917.272051 is its comfortable, ergonomic design. The high-back seat provides ample support during extended mowing sessions, reducing fatigue and improving the overall experience. Additionally, the steering wheel is positioned to offer ease of handling, making it accessible even for users with less experience.

Safety features are also a priority in the design of the 917.272051. The tractor includes a built-in safety switch, which automatically disengages the blades when the operator leaves the seat. This feature adds a crucial layer of safety, protecting users from accidents while ensuring the mower functions efficiently.

Overall, the Craftsman 917.272051 lawn tractor combines power, performance, and user-friendly features, making it an excellent choice for homeowners seeking a dependable tool for lawn care. With its durable construction and advanced technologies, this model is equipped to handle the rigors of regular use, ensuring a well-maintained yard season after season.
Top Page Image Contents