Craftsman 917.272051 owner manual Install Seat, Adjust seat before tightening adjustment knob

Page 9

Label

Terminal

Battery

Door

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

2, Pivot seat upward and remove from the cardboard packing. Remove the

cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolt is positioned over targe slotted hole in pan.

4.Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

5.Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

6.Lower seat into operating position and sit in seat.

7.Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

8.Get off seat without moving its

adjusted position.

8.Raise seat and tighten adjustment knob securely.

Bolt

NOTE: You may now roll or drive you tractor off the skid. Follow the approl: instruction below to remove the tract, from the skid.

TO ROLLTRACTOR OFF SKID (€ Operation section for location al function of controls)

1.Press lift lever plunger and raise attachment tilt lever to its highest

position.

2.Release parking brake by depre,, clutch/brake pedal.

3.Place gearshift lever in neutral (1_ position,

4.Roll tractor forward off skid.

5.Remove banding holding deflect shield up against tractor.

TO DRIVETRACTOR OFF SKID (',

Operation section for location al function of controls)

_WARNING: Before starting, read. understand and follow all instruction',

the Operation section of this manual. sure tractor is in a wel_-ventilatedare

Be sure the area in front of tractor is of other people and objects,

1.Be sure all the above assembly s have been completed.

2, Check engine oil level and fill fu_ tank with gasoline.

3.Sit on seat in operating position, depress clutch/brake pedal and s, the parking brake.

4.Place gear shift lever in neutral (i_ position.

5.Press lift lever plunger and raise attachment lift lever to its highest

position.

6.Start the engine. After engine ha_ started, move throttle control to id

position.

7.Depress clutch/brake pedal into f "BRAKE" position and hold. Mow gearshift lever to 1st gear,

8.Slowly release clutch/brake ped_ s_owly drive tractor off skid.

9.Apply brake to stop tractor, set pa brake and place gearshift lever in neutral position.

10.Turn ignition key to "OFF" positior Continue with the instructions that fo

9

Image 9
Contents Icraftsmanj Limited 90 DAY Warranty on Battery Limited Twoyear Warranty on Craftsman Riding Equipment PartsGeneral Operation Serious injury or deathWhile on the slope Follow the manufacturers recommen Do notAdjust and service as required IV. ServiceHi. Children Responsible adultSafety is Involved Park Plug Product SpecificationsRepair Agreement Customer ResponsibilitiesSteering Remove all accessible loose parts Tools Required for AssemblyHowto SET Upyourtractor Check Battery Before Removingtractor from Skid Attach Steering WheelAdjust seat before tightening adjustment knob Install SeatTo Drivetractor OFF Skid Operation section for location al function of controlsInstall Mulcher Plate R N H L Knowyourtractor Your Tractor Stopping Howto Useyourtractor To SET Parking BrakeEngine To USE Throttle ControlGauge Wheel To Adjust Gauge WheelsTo Operate Mower To Stop Mower BladesBefore Startingthe Engine Check Engine OIL Level Towing Carts and Other AttachmentsADD Gasoline To Start EngineMowingtips Mower should be properly leveled forMulching Mowingtips Lubrication Chart Maintenance ScheduleGeneral Recommendations Before Each USETractor Clean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts Transaxle CoolingMuffler AIR FilterSpark Plugs Engine OIL FilterTo Install Mower CleaningTo Remove Mower Raise attachment lift lever to its highest positionFRONT-TO-BACK Adjustment To Level Mower HousingOn level ground or driveway. Make sure JLiftLink Ustrnent NutTo Adjust Brake Belt InstallationTo Replace Mower Blade Drive Belt Belt RemovalTransaxle Gear Shift Lever Neutral Adjustment To Start Engine with a Weak BatteryTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-INJCAMBERTo Remove Hood and Grill Assembly Replacing BatteryTo Replace Headlight Bulb Interlocks and RelaysAdjusting To Adjust CarburetorCable BracketEngine Fuel System BatferyEngineoil CylindersTroubleshooting Chart ProblemCause Correction Troubleshooting Chart Problem Cause Correction Troubleshooting Chart ProblemcauseTractor - Model Number SchematicElectrical KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917.272051 Chassis and Enclosures KEY Part Description Tractor - Model Number Chassis and EnclosuresTractor - Model Number Ground Drive Description KEY PartTractor - Model Number 917.272051 Steering Assembly KEY Part Description TRACTOR- Model Number Steering AssemblySpark Arrester TRACTOR-- Model NumberTRACTOR- Model Number Seat Assembly Wheels &TIRES DecalsTRACTOR- Model Number Lift Assembly Tractor - Model Number Mower Deck +-j,j+,. lNots Allcomponent dimensions givenin U.S. inches Peerless Transaxle - Model Number 206-545C 778345 @/---L Valve, exhaust Std Blower Housing and Baffles l IGNITION/ELECTRICAL KEY Part Description Blower Housing & Baffles KEY Part DescriptionNot Illustrated AIR INTAKE/FILTRATION KEY Part Description20\ Starting System KEY Part Description OIL PAN/LUBRICATION KEY Part DescriptionEngine Controls KEY Exhaust J Exhaust KEY Part Description Fuel System KEY Part DescriptionPage Page Page Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationGet it fixed, at your home or ours

917.272051 specifications

The Craftsman 917.272051 is a robust and versatile lawn tractor designed to meet the diverse needs of homeowners and landscape enthusiasts. With its powerful engine and user-friendly features, this model stands out in its class, providing a reliable solution for maintaining a pristine lawn.

One of the standout features of the Craftsman 917.272051 is its impressive 20 HP Briggs & Stratton engine. This air-cooled, single-cylinder engine is designed to deliver robust performance, making it easy to tackle a variety of mowing tasks. The engine's reliable starting system ensures minimal downtime, allowing users to efficiently manage their mowing schedule.

The cutting deck of the 917.272051 is another highlight, measuring 42 inches in width. This size strikes a balance between maneuverability and efficiency, enabling users to navigate tight spaces while still covering a generous amount of terrain in one pass. The deck also features a deck wash system, allowing for easy cleaning and maintenance after use, which helps extend its lifespan and maintain optimal performance.

Equipped with a 6-speed transmission, the Craftsman 917.272051 offers users the flexibility to choose the appropriate speed for various mowing conditions. This feature enhances control and allows for a smoother cutting experience, whether tackling overgrown grass or maintaining a manicured lawn.

Another significant aspect of the Craftsman 917.272051 is its comfortable, ergonomic design. The high-back seat provides ample support during extended mowing sessions, reducing fatigue and improving the overall experience. Additionally, the steering wheel is positioned to offer ease of handling, making it accessible even for users with less experience.

Safety features are also a priority in the design of the 917.272051. The tractor includes a built-in safety switch, which automatically disengages the blades when the operator leaves the seat. This feature adds a crucial layer of safety, protecting users from accidents while ensuring the mower functions efficiently.

Overall, the Craftsman 917.272051 lawn tractor combines power, performance, and user-friendly features, making it an excellent choice for homeowners seeking a dependable tool for lawn care. With its durable construction and advanced technologies, this model is equipped to handle the rigors of regular use, ensuring a well-maintained yard season after season.