Craftsman 917.272051 owner manual Before Removingtractor from Skid Attach Steering Wheel

Page 8

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly

easier, Standard wrench sizes you need are listed below,

(1)

9/16" wrench

(1)

Pliers

(2)

1/2" wrench

(1)

Utility knife

(1)Tire pressure gauge

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating position (seated behind the steering wheel).

TO REMOVETRACTOR FROM CARTON

UNPACK CARTON

1, Remove all accessible loose parts

and parts cartons from carton.

2.Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVINGTRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

1.Slide extension shaft onto lower

steering shaft. Align mounting holes in extension and lower shafts and install 5/16 hex bolt and Iocknut.

Tighten securely.

2.Place tabs of steering boot over tab

slots in dash and push down to

secure.

INSTALL STEERING WHEEL

3.Position front wheels of the tractor so they are pointing straight forward.

4.Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5.Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

7.Snap steering wheel insert into center of steering wheel.

8.Remove protective materials from tractor hood and grill.

IMPORTANT." Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid.

HOWTO SET UPYOURTRACTOR

CHECK BATTERY

1.Lift seat pan to raised position and open battery box door.

NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge

battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Icraftsmanj Limited Twoyear Warranty on Craftsman Riding Equipment Parts Limited 90 DAY Warranty on BatterySerious injury or death General OperationWhile on the slope Follow the manufacturers recommen Do notIV. Service Adjust and service as requiredHi. Children Responsible adultSafety is Involved Product Specifications Park PlugRepair Agreement Customer ResponsibilitiesSteering Tools Required for Assembly Remove all accessible loose partsHowto SET Upyourtractor Check Battery Before Removingtractor from Skid Attach Steering WheelInstall Seat Adjust seat before tightening adjustment knobTo Drivetractor OFF Skid Operation section for location al function of controlsInstall Mulcher Plate R N H L Knowyourtractor Your Tractor Howto Useyourtractor To SET Parking Brake StoppingEngine To USE Throttle ControlTo Adjust Gauge Wheels Gauge WheelTo Operate Mower To Stop Mower BladesTowing Carts and Other Attachments Before Startingthe Engine Check Engine OIL LevelADD Gasoline To Start EngineMulching Mowingtips MowingtipsMower should be properly leveled for Maintenance Schedule Lubrication ChartGeneral Recommendations Before Each USETractor Clean AIR Screen Clean AIR INTAKE/COOLING AreasBelts Transaxle CoolingAIR Filter MufflerSpark Plugs Engine OIL FilterCleaning To Install MowerTo Remove Mower Raise attachment lift lever to its highest positionTo Level Mower Housing FRONT-TO-BACK AdjustmentOn level ground or driveway. Make sure JLiftLink Ustrnent NutBelt Installation To Adjust BrakeTo Replace Mower Blade Drive Belt Belt RemovalTo Start Engine with a Weak Battery Transaxle Gear Shift Lever Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-INJCAMBERReplacing Battery To Remove Hood and Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor AdjustingCable BracketBatfery Engine Fuel SystemEngineoil CylindersCause Correction Troubleshooting ChartProblem Troubleshooting Chart Problem Cause Troubleshooting Chart Problemcause CorrectionSchematic Tractor - Model NumberElectrical KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917.272051 Chassis and Enclosures Tractor - Model Number Chassis and Enclosures KEY Part DescriptionTractor - Model Number Ground Drive KEY Part DescriptionTractor - Model Number 917.272051 Steering Assembly TRACTOR- Model Number Steering Assembly KEY Part DescriptionTRACTOR-- Model Number Spark ArresterTRACTOR- Model Number Seat Assembly Decals Wheels &TIRESTRACTOR- Model Number Lift Assembly +-j,j+,. l Tractor - Model Number Mower DeckNots Allcomponent dimensions givenin U.S. inches Peerless Transaxle - Model Number 206-545C 778345 @/---L Valve, exhaust Std Blower Housing and Baffles l Blower Housing & Baffles KEY Part Description IGNITION/ELECTRICAL KEY Part DescriptionNot Illustrated AIR INTAKE/FILTRATION KEY Part Description20\ Engine Controls KEY Starting System KEY Part DescriptionOIL PAN/LUBRICATION KEY Part Description Exhaust J Fuel System KEY Part Description Exhaust KEY Part DescriptionPage Page Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillGet it fixed, at your home or ours

917.272051 specifications

The Craftsman 917.272051 is a robust and versatile lawn tractor designed to meet the diverse needs of homeowners and landscape enthusiasts. With its powerful engine and user-friendly features, this model stands out in its class, providing a reliable solution for maintaining a pristine lawn.

One of the standout features of the Craftsman 917.272051 is its impressive 20 HP Briggs & Stratton engine. This air-cooled, single-cylinder engine is designed to deliver robust performance, making it easy to tackle a variety of mowing tasks. The engine's reliable starting system ensures minimal downtime, allowing users to efficiently manage their mowing schedule.

The cutting deck of the 917.272051 is another highlight, measuring 42 inches in width. This size strikes a balance between maneuverability and efficiency, enabling users to navigate tight spaces while still covering a generous amount of terrain in one pass. The deck also features a deck wash system, allowing for easy cleaning and maintenance after use, which helps extend its lifespan and maintain optimal performance.

Equipped with a 6-speed transmission, the Craftsman 917.272051 offers users the flexibility to choose the appropriate speed for various mowing conditions. This feature enhances control and allows for a smoother cutting experience, whether tackling overgrown grass or maintaining a manicured lawn.

Another significant aspect of the Craftsman 917.272051 is its comfortable, ergonomic design. The high-back seat provides ample support during extended mowing sessions, reducing fatigue and improving the overall experience. Additionally, the steering wheel is positioned to offer ease of handling, making it accessible even for users with less experience.

Safety features are also a priority in the design of the 917.272051. The tractor includes a built-in safety switch, which automatically disengages the blades when the operator leaves the seat. This feature adds a crucial layer of safety, protecting users from accidents while ensuring the mower functions efficiently.

Overall, the Craftsman 917.272051 lawn tractor combines power, performance, and user-friendly features, making it an excellent choice for homeowners seeking a dependable tool for lawn care. With its durable construction and advanced technologies, this model is equipped to handle the rigors of regular use, ensuring a well-maintained yard season after season.
Top Page Image Contents