Craftsman 917.27224 Howto Useyourtractor to SET Parking Brake, Stopping Mower Blades, Engine

Page 14

Theoperationofanytractorcanresultinforeign objects thrown into the /

eyes, which can result in severe eye damage. Always wear safety glasses 1 or eye shields while operating your tractor or performing any ad ustments

or repairs. We recommend a w de v s on safety mask over spectacles, or standard safety glasses.

HOWTO USEYOURTRACTOR TO SET PARKING BRAKE

Your tractor is equipped with an operator

presen.ce sensing switch. When engine Is running, any attempt by the operator to leave the seat withoutfirst setting the parking brake will shut off the engine.

1.Depress brake pedal into full "BRAKE _ position and hold.

2.Place parking brake lever in "EN- GAGED" position and release pressure from brake pedal. Pedal should remain in "BRAKE" position. Make sure parking brake will hold tractor secure.

AttachmentClutch

Push-Into SwitchPullOutTo

"Disengaged_,_En le .

Throttle_,_(_.

o °

 

al

= rive" Disengaged

..

Lever

Position PGsition

PosdJon

STOPPING

MOWER BLADES -

•To stop mower blades,move attach- ment clutch switch to _DISENGAGED"

position,

GROUND DRIVE -

• To stop ground ddve, depress brake

pedal into full =BRAKE" position. IMPORTANT: Forward and reverse drive

pedals retum to neutral position when not

depressed.

ENGINE -

•Move throttle control to slow position. NOTE: Failure to move throttle control to slow position and allowing engine to idle

before stopping may cause engine to _beckfire'.

•Turn ignition key to =OFF" position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

•Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "OFF" will cause the battery to be discharged,

:Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause =browning" of grass. To eliminate this possibility,always stop engine when _Ocpping tractor on grass areas.

AUTION: Always stop tractor completely, as described above, before leaving the operator'sposition; to empty grass catcher, etc.

THROTTLE CONTROL

Always operate engine at full throttle.

•Operating engine at less than full

throttle reduces the battery charging rate.

•Full throttle offers the best bagging and mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you ere starting a cold engine. Do not use to start a warm engine.

•To engage choke control, pull knob out. Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the forward and reverse drive pedals.

1.Start tractor and release parking brake,

2.Slowly depress forward or reverse drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL

The cruise control feature can be used for forward travel only.

1.With forward drive pedal depressed to desired speed, move cruise control lever forward to "SET" position and hold while liftingyour foot off the

pedal, then release the cruise control lever.

To disengage the cruise control, pull the lever backward to "OFF" position, or fully depress the brake pedal.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

•Grasp lift lever.

•Press plunger with thumb and move

14 lever to desired position.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Icrrftsmrni Product Specifications WarrantySafety Rules AssemblyGeneral Operation II. Slope OperationMower blades are sharp and can IV. ServiceNever run a machine inside a clo= area Ifmachinestopswhilegoinguphill Cancer and birth defects or other repro- ductive harmRepair Agreement Product Specifications3ASOLINE 3.5 Gallons Customer ResponsibilitiesSlope Sheet Steering WheelSeat Install Seat Tools Required for AssemblyHowto SET Upyourtractor Check Battery To Removetractor from Carton Unpack CartonCenter Iocknuts and tighten securely Lower seat into operating position and sit in seatAssemble Gaugewheelsto Mower Deck Lower mower linkage with attachment lift control Lock Ut B BracketSlide mower under tractor with Be sure belt tension rod is in disen- gaged positionCheck for Proper Position of ALL Belts Checktire PressureCheck Deck Levelness Check Brake SystemRRN Knowyourtractor Pedal Hourmeter Indicates hours of operationStopping Mower Blades To Adjust Mower Cutting HeightHowto Useyourtractor to SET Parking Brake Ground DriveTo Stop Mower Blades To Adjust Gauge WheelsTo Operate Mower To Operate on HillsTo Start Engine ADD GasolinePurgetransmission Engine warm up periodPulled out slightly Free.wheellever while the engine is runningGeneral Recommendations Lubrication ChartMaintenanceschedule Before Each USEOperator Presence System BatteryTires Blade CareBelts To Clean Battery and TerminalsEngine Lubrication Transaxle Pump FluidTo Service PRE-CLEANER Clean AIR ScreenClean AIR INTAKE/COOLING Areas To Service CartridgeTractor To Install MowerAssembly section of this manual To Remove MowerRaise mower to its highest position SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment Both Front Links Must be Equal LengthCover Clutch Posin Idler To Adjust BrakeRemove belt from electdc clutch pulley To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Adjust Steering Wheel ALIGN- MentTransmission REMOVAL/REPLACE- Ment Front Wheel TOE-IN/CAMBERTo Attachjumper Cables To Start Engine with a Weak BatteryReplacing Battery To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Preliminary SettingWise 1 tum Final SettingRecheck idle speed. Readjust if necessary Acceleration TestEngine OIL To Clean Battery and TermiTractor CylindersTroubleshoongchart Problem Cause CorrectionCause Troubleshooting ChartProblem CorrectionCause OFFTRACTOR-- Model Number Schematic SeatswitchTractor - Model Number Electrical TRACTOR-- Model Number Electrical KEY Part DescriptionTRACTOR- -MODELNUMBER917.272240 Chassisandenclosures Tractor - Model Number 9t7.272240 Chassis and Enclosures TRACTOR- -MODEL NUM BER Ground Drive TRACTOR- Model Number Ground Drive 250TRACTOR- -MODEL Number Steering Assembly TRACTOR-- Model Number 917.272240 Steeringassembly TRACTOR- Model Number Engine Tractor - Model Number Engine TRACTOR- Model Number Seat Assembly KEY Part NO. NO. DescriptionTRACTOR- Model Number Decals Description KEY PartTractor - Model Number Liftassembly TRACTOR-- Model Number Liftassembly 37 123935X Plug Hole 38 17066516 Screw 5/16-18 xTRACTOR- -MODEL Number Mowerdeck Tractor - Model Number Mowerdeck 5116-18 x 5/8Oe oo 032 Ift22 KEY Part NO. no Description Descripon Blower Housing and Baffles Ignitionicharging KEY Part Description Starting System I Engine Controls KEY Part Description NO. no Crankshaft J Exhaustj Exhaust Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Canada Part

917.27224 specifications

The Craftsman 917.27224 is a reliable and versatile riding lawn mower designed for homeowners seeking efficiency and comfort while maintaining their lawns. This model is known for its robust construction, innovative features, and user-friendly design, making it a popular choice among gardening enthusiasts.

One of the standout features of the Craftsman 917.27224 is its powerful engine. It is equipped with a dependable Briggs & Stratton engine, which provides ample horsepower for cutting through thick grass and tackling uneven terrain. This engine is designed for easy start-up and smooth operation, ensuring that mowing tasks can be completed efficiently.

The mower also boasts a 42-inch cutting deck, which allows for a wide swath of grass to be cut in a single pass. This feature not only saves time but also enhances the overall mowing experience. The cutting height can be easily adjusted to meet individual preferences and grass conditions, providing flexibility for different lawn types and seasons.

In terms of technology, the Craftsman 917.27224 includes an automatic transmission system that simplifies operation. Riders can shift gears effortlessly without the need for manual clutching, allowing for a smoother ride and more precise control over speed. This feature is particularly beneficial for users who may be new to riding mowers, as it enhances their confidence while operating the machine.

Comfort is also a priority with the Craftsman 917.27224. It features a comfortable, cushioned seat designed with ergonomics in mind, reducing fatigue during longer mowing sessions. Additionally, the mower is built with easy-to-access controls, allowing the operator to adjust settings or disengage the blades without hassle.

Safety features are not overlooked in this model. The mower comes with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidental injuries. Furthermore, the durable construction of the Craftsman 917.27224 is designed to withstand the rigors of regular use, ensuring longevity and protecting the investment.

In conclusion, the Craftsman 917.27224 stands out in the riding mower market. With its powerful engine, wide cutting deck, user-friendly automatic transmission, and comfort-focused design, it meets the needs of homeowners looking for a reliable lawn maintenance solution. Its emphasis on safety and durability makes it a worthwhile choice for anyone wanting to keep their lawn in pristine condition.
Top Page Image Contents