Craftsman 917.27224 manual Cause, Off

Page 32

TROUBLESHOOTINGCHART

PROBLEM

Poorg_ss discha_e

CAUSE

1.Engine speed too slow,

2.Travel speed too fast.

3, Wet grass,

4. Mower deck not level.

CORRECTION

1.Place throttle control in "FAST" position.

2.Shift to slower speed.

3.Allow grass to dry before mowing.

4.Level mower deck.

5. Low/uneven tire air pressure, 5. Check tires for proper air

6.Worn, bent or loose blade,

7, Buildup of grass, leavesand trash under mower,

8, Mower drive belt worn.

9.Blades impropody installed. 10.Improper blades used.

pressure.

6.Replace/sharpen blade. Tighten blade bolt.

7.Clean underside of mower housing.

8.Replace mower drive belt.

9, Reinstall blades sharp edge down.

10, Replace with blades listed in this manual.

Headlight(s)not working

ifso equipped)

3attery will not

:harge

_OSS of drive

11,Clogged mower deck vent

11.Clean around mandrels to

holes from buildup of

open vent holes,

grass, leaves, and trash

 

around mandrels,

 

1. Switch is "OFF".

1. Turn switch "ON".

2.Bulb(s) or lamp(s) burned 2. Replace bulb(s) or Lamp(s). out.

3.Faulty light switch,3. Checldreplace light switch.

4.

Loose

or damaged wiring.

4.

Check wiring and connec-

5.

Blown

fuse.

 

tions.

 

 

5.

Replace fuse,

1.

Bad battery cell(s).

1.

Replace

battery.

2.

Poor cable connections,

2.

Check/clean

all connec-

 

 

 

 

tions.

 

 

13.

Faulty regulator

3.

Replace

regulator.

 

(if so equipped).

 

Replace

alternator.

4.

Faulty alternator.

4.

1.

Freewheel control in

1.

Place freewheel control in

 

"disengaged" position.

 

"engaged"

position.

2,

Motion drive belt worn,

2.

Replace motion drive belt.

 

damaged, or broken.

 

 

 

 

3.Air trapped in transmission 3. Purge transmission. during shipment or

servicing.

Engine"backfires"

1. Engine throttle control not

1. Move throttle control to

_henturning

set at "SLOW"

"SLOVV_ position and allow

engine

position for 30 seconds

to idle for 30 seconds before

"OFF"

before stopping engine,

stopping engine.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Icrrftsmrni Warranty Safety RulesProduct Specifications AssemblyGeneral Operation II. Slope OperationMower blades are sharp and can IV. ServiceNever run a machine inside a clo= area Ifmachinestopswhilegoinguphill Cancer and birth defects or other repro- ductive harmProduct Specifications 3ASOLINE 3.5 GallonsRepair Agreement Customer ResponsibilitiesSlope Sheet Steering WheelSeat Tools Required for Assembly Howto SET Upyourtractor Check BatteryInstall Seat To Removetractor from Carton Unpack CartonCenter Iocknuts and tighten securely Lower seat into operating position and sit in seatAssemble Gaugewheelsto Mower Deck Lock Ut B Bracket Slide mower under tractor withLower mower linkage with attachment lift control Be sure belt tension rod is in disen- gaged positionChecktire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemRRN Knowyourtractor Pedal Hourmeter Indicates hours of operationTo Adjust Mower Cutting Height Howto Useyourtractor to SET Parking BrakeStopping Mower Blades Ground DriveTo Adjust Gauge Wheels To Operate MowerTo Stop Mower Blades To Operate on HillsTo Start Engine ADD GasolineEngine warm up period Pulled out slightlyPurgetransmission Free.wheellever while the engine is runningLubrication Chart MaintenancescheduleGeneral Recommendations Before Each USEBattery TiresOperator Presence System Blade CareTo Clean Battery and Terminals Engine LubricationBelts Transaxle Pump FluidClean AIR Screen Clean AIR INTAKE/COOLING AreasTo Service PRE-CLEANER To Service CartridgeTo Install Mower Assembly section of this manualTractor To Remove MowerSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentRaise mower to its highest position Both Front Links Must be Equal LengthTo Adjust Brake Remove belt from electdc clutch pulleyCover Clutch Posin Idler To Replace Mower Blade Drive BeltTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACE- MentTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery Replacing BatteryTo Attachjumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingFinal Setting Recheck idle speed. Readjust if necessaryWise 1 tum Acceleration TestTo Clean Battery and Termi TractorEngine OIL CylindersTroubleshoongchart Problem Cause CorrectionTroubleshooting Chart ProblemCause CorrectionCause OFFTRACTOR-- Model Number Schematic SeatswitchTractor - Model Number Electrical TRACTOR-- Model Number Electrical KEY Part DescriptionTRACTOR- -MODELNUMBER917.272240 Chassisandenclosures Tractor - Model Number 9t7.272240 Chassis and Enclosures TRACTOR- -MODEL NUM BER Ground Drive TRACTOR- Model Number Ground Drive 250TRACTOR- -MODEL Number Steering Assembly TRACTOR-- Model Number 917.272240 Steeringassembly TRACTOR- Model Number Engine Tractor - Model Number Engine TRACTOR- Model Number Seat Assembly KEY Part NO. NO. DescriptionTRACTOR- Model Number Decals Description KEY PartTractor - Model Number Liftassembly TRACTOR-- Model Number Liftassembly 37 123935X Plug Hole 38 17066516 Screw 5/16-18 xTRACTOR- -MODEL Number Mowerdeck Tractor - Model Number Mowerdeck 5116-18 x 5/8Oe oo 032 Ift22 KEY Part NO. no Description Descripon Blower Housing and Baffles Ignitionicharging KEY Part Description Starting System I Engine Controls KEY Part Description NO. no Crankshaft J Exhaustj Exhaust Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Canada Part

917.27224 specifications

The Craftsman 917.27224 is a reliable and versatile riding lawn mower designed for homeowners seeking efficiency and comfort while maintaining their lawns. This model is known for its robust construction, innovative features, and user-friendly design, making it a popular choice among gardening enthusiasts.

One of the standout features of the Craftsman 917.27224 is its powerful engine. It is equipped with a dependable Briggs & Stratton engine, which provides ample horsepower for cutting through thick grass and tackling uneven terrain. This engine is designed for easy start-up and smooth operation, ensuring that mowing tasks can be completed efficiently.

The mower also boasts a 42-inch cutting deck, which allows for a wide swath of grass to be cut in a single pass. This feature not only saves time but also enhances the overall mowing experience. The cutting height can be easily adjusted to meet individual preferences and grass conditions, providing flexibility for different lawn types and seasons.

In terms of technology, the Craftsman 917.27224 includes an automatic transmission system that simplifies operation. Riders can shift gears effortlessly without the need for manual clutching, allowing for a smoother ride and more precise control over speed. This feature is particularly beneficial for users who may be new to riding mowers, as it enhances their confidence while operating the machine.

Comfort is also a priority with the Craftsman 917.27224. It features a comfortable, cushioned seat designed with ergonomics in mind, reducing fatigue during longer mowing sessions. Additionally, the mower is built with easy-to-access controls, allowing the operator to adjust settings or disengage the blades without hassle.

Safety features are not overlooked in this model. The mower comes with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidental injuries. Furthermore, the durable construction of the Craftsman 917.27224 is designed to withstand the rigors of regular use, ensuring longevity and protecting the investment.

In conclusion, the Craftsman 917.27224 stands out in the riding mower market. With its powerful engine, wide cutting deck, user-friendly automatic transmission, and comfort-focused design, it meets the needs of homeowners looking for a reliable lawn maintenance solution. Its emphasis on safety and durability makes it a worthwhile choice for anyone wanting to keep their lawn in pristine condition.
Top Page Image Contents