Craftsman 917.27224 manual Wise 1 tum, Final Setting, Recheck idle speed. Readjust if necessary

Page 28

2. With engine off turn idle fuel adjusting needle in (clockwise) closing it finger tight and then turn out (counterclock-

wise) 1 tum.

FINAL SETTING -

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

NOTE: The high idle is set at the factory and cannot be adjusted.

2.Idle soeed settina - With throttle

control lever in slow position, engine should idle at 1200 RPM. If engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is attained.

3.Idle fuel needle settin9 - With throttle control lever in slow position, turn idle fuel adjusting needle in (clockwise) until engine speed decreases and then turn out (counterclockwise) approximately 3/4 turn to obtain the beat low speed performance.

4.Recheck idle speed. Readjust if necessary,

ACCELERATION TEST -

5. Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle fuel adjusting needle out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust-damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed settingcan be dangerous. If you think the engine-governed high speed needs adjusting, contact your nearest Sears or other qualified service center, which has proper equipment and expedence to make any necessary adjustments.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Icrrftsmrni Warranty Safety RulesProduct Specifications AssemblyGeneral Operation II. Slope OperationNever run a machine inside a clo= area IV. ServiceMower blades are sharp and can Ifmachinestopswhilegoinguphill Cancer and birth defects or other repro- ductive harmProduct Specifications 3ASOLINE 3.5 GallonsRepair Agreement Customer ResponsibilitiesSeat Steering WheelSlope Sheet Tools Required for Assembly Howto SET Upyourtractor Check BatteryInstall Seat To Removetractor from Carton Unpack CartonAssemble Gaugewheelsto Mower Deck Lower seat into operating position and sit in seatCenter Iocknuts and tighten securely Lock Ut B Bracket Slide mower under tractor withLower mower linkage with attachment lift control Be sure belt tension rod is in disen- gaged positionChecktire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemRRN Knowyourtractor Pedal Hourmeter Indicates hours of operationTo Adjust Mower Cutting Height Howto Useyourtractor to SET Parking BrakeStopping Mower Blades Ground DriveTo Adjust Gauge Wheels To Operate MowerTo Stop Mower Blades To Operate on HillsTo Start Engine ADD GasolineEngine warm up period Pulled out slightlyPurgetransmission Free.wheellever while the engine is runningLubrication Chart MaintenancescheduleGeneral Recommendations Before Each USEBattery TiresOperator Presence System Blade CareTo Clean Battery and Terminals Engine LubricationBelts Transaxle Pump FluidClean AIR Screen Clean AIR INTAKE/COOLING AreasTo Service PRE-CLEANER To Service CartridgeTo Install Mower Assembly section of this manualTractor To Remove MowerSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentRaise mower to its highest position Both Front Links Must be Equal LengthTo Adjust Brake Remove belt from electdc clutch pulleyCover Clutch Posin Idler To Replace Mower Blade Drive BeltTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACE- MentTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery Replacing BatteryTo Attachjumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingFinal Setting Recheck idle speed. Readjust if necessaryWise 1 tum Acceleration TestTo Clean Battery and Termi TractorEngine OIL CylindersTroubleshoongchart Problem Cause CorrectionTroubleshooting Chart ProblemCause CorrectionCause OFFTRACTOR-- Model Number Schematic SeatswitchTractor - Model Number Electrical TRACTOR-- Model Number Electrical KEY Part DescriptionTRACTOR- -MODELNUMBER917.272240 Chassisandenclosures Tractor - Model Number 9t7.272240 Chassis and Enclosures TRACTOR- -MODEL NUM BER Ground Drive TRACTOR- Model Number Ground Drive 250TRACTOR- -MODEL Number Steering Assembly TRACTOR-- Model Number 917.272240 Steeringassembly TRACTOR- Model Number Engine Tractor - Model Number Engine TRACTOR- Model Number Seat Assembly KEY Part NO. NO. DescriptionTRACTOR- Model Number Decals Description KEY PartTractor - Model Number Liftassembly TRACTOR-- Model Number Liftassembly 37 123935X Plug Hole 38 17066516 Screw 5/16-18 xTRACTOR- -MODEL Number Mowerdeck Tractor - Model Number Mowerdeck 5116-18 x 5/8Oe oo 032 Ift22 KEY Part NO. no Description Descripon Blower Housing and Baffles Ignitionicharging KEY Part Description Starting System I Engine Controls KEY Part Description NO. no Crankshaft J Exhaustj Exhaust Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Canada Part

917.27224 specifications

The Craftsman 917.27224 is a reliable and versatile riding lawn mower designed for homeowners seeking efficiency and comfort while maintaining their lawns. This model is known for its robust construction, innovative features, and user-friendly design, making it a popular choice among gardening enthusiasts.

One of the standout features of the Craftsman 917.27224 is its powerful engine. It is equipped with a dependable Briggs & Stratton engine, which provides ample horsepower for cutting through thick grass and tackling uneven terrain. This engine is designed for easy start-up and smooth operation, ensuring that mowing tasks can be completed efficiently.

The mower also boasts a 42-inch cutting deck, which allows for a wide swath of grass to be cut in a single pass. This feature not only saves time but also enhances the overall mowing experience. The cutting height can be easily adjusted to meet individual preferences and grass conditions, providing flexibility for different lawn types and seasons.

In terms of technology, the Craftsman 917.27224 includes an automatic transmission system that simplifies operation. Riders can shift gears effortlessly without the need for manual clutching, allowing for a smoother ride and more precise control over speed. This feature is particularly beneficial for users who may be new to riding mowers, as it enhances their confidence while operating the machine.

Comfort is also a priority with the Craftsman 917.27224. It features a comfortable, cushioned seat designed with ergonomics in mind, reducing fatigue during longer mowing sessions. Additionally, the mower is built with easy-to-access controls, allowing the operator to adjust settings or disengage the blades without hassle.

Safety features are not overlooked in this model. The mower comes with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidental injuries. Furthermore, the durable construction of the Craftsman 917.27224 is designed to withstand the rigors of regular use, ensuring longevity and protecting the investment.

In conclusion, the Craftsman 917.27224 stands out in the riding mower market. With its powerful engine, wide cutting deck, user-friendly automatic transmission, and comfort-focused design, it meets the needs of homeowners looking for a reliable lawn maintenance solution. Its emphasis on safety and durability makes it a worthwhile choice for anyone wanting to keep their lawn in pristine condition.
Top Page Image Contents