Craftsman 917.27224 manual Tractor, To Clean Battery and Termi, Engine OIL, Cylinders, Other

Page 29

Immediatelyprepareyourtractorfor

storage at the end of the season or if the

tractor will not be used for 30 days or more.

I,CAUTION: Never store the trectorwith gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly,

remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire tractor (See "CLEANING" in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Mainte- nance section of this manual.

4.Be sure that all nuts, bolts and screws

are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BA'n'ERY

Fully charge the battery for storage.

After a period of time in storage, battery may require recharging.

To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected

and battery cleaned thoroughly (see

"TO CLEAN BATTERY AND TERMI-

NALS" in the Maintenance section of this manual).

After cleaning, leave cables discon- nected and place cables where they cannot come in contact with battery terminals.

If battery is removed from tractorfor storage, do not store battery directly on concrete or damp surfaces.

ENGINE

expedance indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids dudng storage. Acidic gas can damage the fuel system of and engine while in storage.

1.Drain the fuel tank.

2.Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or

storage container. Always follow the mix ratio found on stabilizer container. Run

engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach

the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See =ENGINE" in the Maintenance section of this manual).

CYLINDER(S)

1.Remove spark plug(s).

2.Pour one ounce of oil through spark plug hole(s) into cylinder(s).

3.Turn ignitionkey to =START" position for a few seconds to distributeoil.

4.Replace with new spark plug(s).

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust aed/or dirt in your gasoline will cause problems.

If possible, store your tractor indoors and cover it to give protection from dust and dirt.

Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows conden-

sation to form and will cause your tractorto rust.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposites from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also,

IMPORTANT: Never cover tractor while engine and exhaust areas are still warm.

29

Image 29
Contents Icrrftsmrni Safety Rules WarrantyProduct Specifications AssemblyII. Slope Operation General OperationMower blades are sharp and can IV. ServiceNever run a machine inside a clo= area Cancer and birth defects or other repro- ductive harm Ifmachinestopswhilegoinguphill3ASOLINE 3.5 Gallons Product SpecificationsRepair Agreement Customer ResponsibilitiesSlope Sheet Steering WheelSeat Howto SET Upyourtractor Check Battery Tools Required for AssemblyInstall Seat To Removetractor from Carton Unpack CartonCenter Iocknuts and tighten securely Lower seat into operating position and sit in seatAssemble Gaugewheelsto Mower Deck Slide mower under tractor with Lock Ut B BracketLower mower linkage with attachment lift control Be sure belt tension rod is in disen- gaged positionCheck Deck Levelness Checktire PressureCheck for Proper Position of ALL Belts Check Brake SystemRRN Pedal Hourmeter Indicates hours of operation KnowyourtractorHowto Useyourtractor to SET Parking Brake To Adjust Mower Cutting HeightStopping Mower Blades Ground DriveTo Operate Mower To Adjust Gauge WheelsTo Stop Mower Blades To Operate on HillsADD Gasoline To Start EnginePulled out slightly Engine warm up periodPurgetransmission Free.wheellever while the engine is runningMaintenanceschedule Lubrication ChartGeneral Recommendations Before Each USETires BatteryOperator Presence System Blade CareEngine Lubrication To Clean Battery and TerminalsBelts Transaxle Pump FluidClean AIR INTAKE/COOLING Areas Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeAssembly section of this manual To Install MowerTractor To Remove MowerFRONT-TO-BACK Adjustment SIDE-TO-SIDE AdjustmentRaise mower to its highest position Both Front Links Must be Equal LengthRemove belt from electdc clutch pulley To Adjust BrakeCover Clutch Posin Idler To Replace Mower Blade Drive BeltTransmission REMOVAL/REPLACE- Ment To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBERReplacing Battery To Start Engine with a Weak BatteryTo Attachjumper Cables To Remove CABLES, Reverse OrderTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Preliminary SettingRecheck idle speed. Readjust if necessary Final SettingWise 1 tum Acceleration TestTractor To Clean Battery and TermiEngine OIL CylindersCause Correction Troubleshoongchart ProblemProblem Troubleshooting ChartCause CorrectionOFF CauseSeatswitch TRACTOR-- Model Number SchematicTractor - Model Number Electrical KEY Part Description TRACTOR-- Model Number ElectricalTRACTOR- -MODELNUMBER917.272240 Chassisandenclosures Tractor - Model Number 9t7.272240 Chassis and Enclosures TRACTOR- -MODEL NUM BER Ground Drive 250 TRACTOR- Model Number Ground DriveTRACTOR- -MODEL Number Steering Assembly TRACTOR-- Model Number 917.272240 Steeringassembly TRACTOR- Model Number Engine Tractor - Model Number Engine KEY Part NO. NO. Description TRACTOR- Model Number Seat AssemblyDescription KEY Part TRACTOR- Model Number DecalsTractor - Model Number Liftassembly 37 123935X Plug Hole 38 17066516 Screw 5/16-18 x TRACTOR-- Model Number LiftassemblyTRACTOR- -MODEL Number Mowerdeck 5116-18 x 5/8 Tractor - Model Number MowerdeckOe oo 032 Ift22 KEY Part NO. no Description Descripon Blower Housing and Baffles Ignitionicharging KEY Part Description Starting System I Engine Controls KEY Part Description NO. no Crankshaft J Exhaustj Exhaust Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Part Canada

917.27224 specifications

The Craftsman 917.27224 is a reliable and versatile riding lawn mower designed for homeowners seeking efficiency and comfort while maintaining their lawns. This model is known for its robust construction, innovative features, and user-friendly design, making it a popular choice among gardening enthusiasts.

One of the standout features of the Craftsman 917.27224 is its powerful engine. It is equipped with a dependable Briggs & Stratton engine, which provides ample horsepower for cutting through thick grass and tackling uneven terrain. This engine is designed for easy start-up and smooth operation, ensuring that mowing tasks can be completed efficiently.

The mower also boasts a 42-inch cutting deck, which allows for a wide swath of grass to be cut in a single pass. This feature not only saves time but also enhances the overall mowing experience. The cutting height can be easily adjusted to meet individual preferences and grass conditions, providing flexibility for different lawn types and seasons.

In terms of technology, the Craftsman 917.27224 includes an automatic transmission system that simplifies operation. Riders can shift gears effortlessly without the need for manual clutching, allowing for a smoother ride and more precise control over speed. This feature is particularly beneficial for users who may be new to riding mowers, as it enhances their confidence while operating the machine.

Comfort is also a priority with the Craftsman 917.27224. It features a comfortable, cushioned seat designed with ergonomics in mind, reducing fatigue during longer mowing sessions. Additionally, the mower is built with easy-to-access controls, allowing the operator to adjust settings or disengage the blades without hassle.

Safety features are not overlooked in this model. The mower comes with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidental injuries. Furthermore, the durable construction of the Craftsman 917.27224 is designed to withstand the rigors of regular use, ensuring longevity and protecting the investment.

In conclusion, the Craftsman 917.27224 stands out in the riding mower market. With its powerful engine, wide cutting deck, user-friendly automatic transmission, and comfort-focused design, it meets the needs of homeowners looking for a reliable lawn maintenance solution. Its emphasis on safety and durability makes it a worthwhile choice for anyone wanting to keep their lawn in pristine condition.