Craftsman 917.27224 Tires, Operator Presence System, Blade Care, To Sharpen Blade, Blade Removal

Page 19

TRACTOR

Alwaysobservesafetyruleswhen performinganymaintenance.

BRAKEOPERATION Iftractorrequiresmorethansix(6)feet

stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the

Service and Adjustments section of this

manual).

TIRES

•Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage,

NOTE: To seal tire punctures and p_event fiat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure that operator presence and intedock systems are working properly. If your tractor does not function as de- scribed below, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachment clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat withoutfirst setting the parking brake should shut off the engine.

•When the engine is running and the attachment dutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp, Replace bent or damaged blades.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble hex bolt, lock washer and fiat washer in exact order as shown.

5.Tighten bolt securely (45-55 Ft. Lbs. torque),

TrailingEdgeUp j_ _, MandreI

_,_ Sta_Assembly

Flat Washer__Cente

r

Lock

""_>_'__

Hole

Washer

J_

_-_

_-T"_- Blade

_,,

 

HexBolt

_3

 

(Grade 8)*

 

*A Grade 8 heat treatedbolt can be identifiedby sixlineson the bolt head.

IMPORTANT: Blade belt is grade 8 heat treated.

TO SHARPEN BLADE

NOTE: We do not recommend sharpen- ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual

damage to mower and engine.

•The blade can be sharpened with a file or on a gdnding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel belt, pin, or a cone balancer. (When using a cone bal-

ancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreeded

portion of the steel bolt or pin and hold the belt or pin parallel with the ground.

If blade is balanced, it should remain in a hedzontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center Hole

BLADE REMOVAL

1, Raise mower to highest position to allow access to blades,

2.Remove hex bolt, lock washer and fiat washer secudng blade,

3.Install new or resharpened blade with trailing edge up towards deck as shown.

" Blade

or Pin -_

BATTERY

Your tractor has a battery charging system which is sufficientfor normal use. How-

ever, periodic charging of the battery with 19an automotive charger will extend its life.

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Icrrftsmrni Assembly WarrantySafety Rules Product SpecificationsII. Slope Operation General OperationNever run a machine inside a clo= area IV. ServiceMower blades are sharp and can Cancer and birth defects or other repro- ductive harm IfmachinestopswhilegoinguphillCustomer Responsibilities Product Specifications3ASOLINE 3.5 Gallons Repair AgreementSeat Steering WheelSlope Sheet To Removetractor from Carton Unpack Carton Tools Required for AssemblyHowto SET Upyourtractor Check Battery Install SeatAssemble Gaugewheelsto Mower Deck Lower seat into operating position and sit in seatCenter Iocknuts and tighten securely Be sure belt tension rod is in disen- gaged position Lock Ut B BracketSlide mower under tractor with Lower mower linkage with attachment lift controlCheck Brake System Checktire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsRRN Pedal Hourmeter Indicates hours of operation KnowyourtractorGround Drive To Adjust Mower Cutting HeightHowto Useyourtractor to SET Parking Brake Stopping Mower BladesTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To Stop Mower BladesADD Gasoline To Start EngineFree.wheellever while the engine is running Engine warm up periodPulled out slightly PurgetransmissionBefore Each USE Lubrication ChartMaintenanceschedule General RecommendationsBlade Care BatteryTires Operator Presence SystemTransaxle Pump Fluid To Clean Battery and TerminalsEngine Lubrication BeltsTo Service Cartridge Clean AIR ScreenClean AIR INTAKE/COOLING Areas To Service PRE-CLEANERTo Remove Mower To Install MowerAssembly section of this manual TractorBoth Front Links Must be Equal Length SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment Raise mower to its highest positionTo Replace Mower Blade Drive Belt To Adjust BrakeRemove belt from electdc clutch pulley Cover Clutch Posin IdlerFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTransmission REMOVAL/REPLACE- Ment To Replace Motion Drive BeltTo Remove CABLES, Reverse Order To Start Engine with a Weak BatteryReplacing Battery To Attachjumper CablesPreliminary Setting To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorAcceleration Test Final SettingRecheck idle speed. Readjust if necessary Wise 1 tumCylinders To Clean Battery and TermiTractor Engine OILCause Correction Troubleshoongchart ProblemCorrection Troubleshooting ChartProblem CauseOFF CauseSeatswitch TRACTOR-- Model Number SchematicTractor - Model Number Electrical KEY Part Description TRACTOR-- Model Number ElectricalTRACTOR- -MODELNUMBER917.272240 Chassisandenclosures Tractor - Model Number 9t7.272240 Chassis and Enclosures TRACTOR- -MODEL NUM BER Ground Drive 250 TRACTOR- Model Number Ground DriveTRACTOR- -MODEL Number Steering Assembly TRACTOR-- Model Number 917.272240 Steeringassembly TRACTOR- Model Number Engine Tractor - Model Number Engine KEY Part NO. NO. Description TRACTOR- Model Number Seat AssemblyDescription KEY Part TRACTOR- Model Number DecalsTractor - Model Number Liftassembly 37 123935X Plug Hole 38 17066516 Screw 5/16-18 x TRACTOR-- Model Number LiftassemblyTRACTOR- -MODEL Number Mowerdeck 5116-18 x 5/8 Tractor - Model Number MowerdeckOe oo 032 Ift22 KEY Part NO. no Description Descripon Blower Housing and Baffles Ignitionicharging KEY Part Description Starting System I Engine Controls KEY Part Description NO. no Crankshaft J Exhaustj Exhaust Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Part Canada

917.27224 specifications

The Craftsman 917.27224 is a reliable and versatile riding lawn mower designed for homeowners seeking efficiency and comfort while maintaining their lawns. This model is known for its robust construction, innovative features, and user-friendly design, making it a popular choice among gardening enthusiasts.

One of the standout features of the Craftsman 917.27224 is its powerful engine. It is equipped with a dependable Briggs & Stratton engine, which provides ample horsepower for cutting through thick grass and tackling uneven terrain. This engine is designed for easy start-up and smooth operation, ensuring that mowing tasks can be completed efficiently.

The mower also boasts a 42-inch cutting deck, which allows for a wide swath of grass to be cut in a single pass. This feature not only saves time but also enhances the overall mowing experience. The cutting height can be easily adjusted to meet individual preferences and grass conditions, providing flexibility for different lawn types and seasons.

In terms of technology, the Craftsman 917.27224 includes an automatic transmission system that simplifies operation. Riders can shift gears effortlessly without the need for manual clutching, allowing for a smoother ride and more precise control over speed. This feature is particularly beneficial for users who may be new to riding mowers, as it enhances their confidence while operating the machine.

Comfort is also a priority with the Craftsman 917.27224. It features a comfortable, cushioned seat designed with ergonomics in mind, reducing fatigue during longer mowing sessions. Additionally, the mower is built with easy-to-access controls, allowing the operator to adjust settings or disengage the blades without hassle.

Safety features are not overlooked in this model. The mower comes with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidental injuries. Furthermore, the durable construction of the Craftsman 917.27224 is designed to withstand the rigors of regular use, ensuring longevity and protecting the investment.

In conclusion, the Craftsman 917.27224 stands out in the riding mower market. With its powerful engine, wide cutting deck, user-friendly automatic transmission, and comfort-focused design, it meets the needs of homeowners looking for a reliable lawn maintenance solution. Its emphasis on safety and durability makes it a worthwhile choice for anyone wanting to keep their lawn in pristine condition.
Top Page Image Contents