Nilfisk-ALTO 3.4 user manual 2 u S, Edit menu, Input Gain

Page 17

The values can be set in the following ranges:

0 P 1

D E L A Y

2 9 2 u S

The values can be set in the following ranges:

OUTPUT DELAY

	OUTPUT 1	OP1 DELAY=
	HIGH	0ms
	18ms(6 5m)
4ms	14ms(5m)
	OUTPUT 3	OP3 DELAY=
	LOW	4ms
		4ms

OUTPUT DELAY

unit

range

step

0.0 ~ 100.0

0.5

0 ~ 100000

0 ~ 291

0 ~ 291271

OUTPUT DELAY

Loudspeaker

Delayed Virtual

Components

Alignment #1

Alignment #2

5.3Edit menu

The values can be set in the following ranges:

EDIT

Input Gain	Parameters
Input EQ	Parameters
Xover	Parameters
Output EQ	Parameters
Output Gain	Parameters
Output Pol.	Parameters
Output Limiter	Parameters

Parameters	In these pages, the number of the parameters and how they are presented varies according

to the configuration of the PRESET and according to Ganging and Units settings (UTILITY menu). In fact, these pages only show the parameters that can actually be used, in the most suitable form of editing.

5.3.1 Input Gain

Input gain control.

Image 17

Contents MAXIDRIVE3.4 Important Safety Instructions Safety Related SymbolsPower Supply External ConnectionPreface Table of Contents Introduction Rear Panel Getting Started Configuration of the systemOutputs Inputs3 B 2 4 S 5 2 x 2 W + 2 M a 3 5 B 2 4 2 x 3 W Adjusting the input signalA d P r e s e t 2 x 3 W P u t I nSystem configuration 3 B 2 4 S 5 2 x 2 W + 2 M a First SetupA G a I N D B A & B G a I NType of Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExampleMenu MAP Configuration Description Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M aPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D O r e P r e s e t 2 x 2 W + 2 M a Store & Naming PresetO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M aIncoming Dump Dump Out PresetT P r e s e t 2 W + 2 M a C o m i n g D u m p N o r e C e p t Delay Menu L a Y P u t D e l a yM S T p u tInput Gain 2 u SEdit menu D B I NP u t Input EQGain Centre Frequency / Cutoff FrequencyBandwidth 0 0 H z V e rR u F B e s 2 Phase4 6 H z Crossover frequencyOutput Gain Output EQEditing values are between +6dB ~ -30dB, with 0.5dB steps Output PolV e r s e L a R I T YR m a Ganging Submenu Utility MenuInput Ganging N g i n gP u t G a n g i n g M . T h r e s h . U n i t T p u t G a n g i n gM P e r a t u r e U n i t Units SubmenuT p u t M e t e r s E M u t e S t M u t e T u pP u t S e l e c t G i t a l A l o g K e U p R m a l T e M p e r a t u r eD C o n t r a s t Lock SubmenuTotal Partial C k2 2 W + 2 M a 3 B 2 4 S 5 L O C K A 1 3 B 2 4 S 5 2 2 W + 2 M aS s w o r d S s w o r d R DR m a t R d COMM. Setup SubmenuR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u pInputs a & B ConnectionsInputs a & B, Digital IN, RS485 Outputs 1 ~ 6, RS485 OUT Factory Preset ConfigurationRS232 Special attentions for RS232 interfaceOrganization Signal PowerA135 B246 3-WAY Stereo 2X2W Audio Mixer Signal PowerMAXIDRIVE3.4 High Left High Right Signal Power Audio MixerA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX To / from RS232 Communications PC & one or more MAXIDRIVE3.4 connectionTechnical Specifications Terms and Conditions Warranty Registration CardReturn Notice Seikaku Technical Group Limited