Nilfisk-ALTO 3.4 user manual 3 B 2 4 S 5 2 x 2 W + 2 M a, A d P r e s e t 2 x 3 W, P u t I n

Page 8

And the system Will enter into default status, showing the main operating information on the display.

A 1 3 B 2 4 S 5 6

2F 2 x 2 W + 2 M A X

Set all the MAXIDRIVE3.4 outputs in MUTE status (LEDs lit) by pressing the relative keys.

Load the Factory PRESET containing the configuration you've found.

Press the MODE Key until the PRESET menu LED lights up.

The display will show the Load PRESET page:

L o a d P r e s e t

3 F 2 x 3 W

(example)

Use the DIAL to find the necessary Factory PRESET (indicated by the letter F). Check that if, among the PRESETS available, there are already some optimised for the specific speaker enclosures being used.

Press ENTER.

The display shows the PRESET loaded in the units memory and the relative configuration:

A 1 3 5 B 2 4 6

3 F 2 x 3 W

4.2 Adjusting the input signal

(example)

It is much more important to set the input signal of a digital unit than that of an analog unit, because excessively high input signals will make any saturation of the A/D converters cause a typical particularly distinct noise (high level square wave).

Proceed as follows:

Keep the MAXIDRIVE3.4 outputs in MUTE status (LEDs light on).

Feed a signal in on the MAXIDRIVE3.4's input and watch the INPUT LEVEL A-BLED ladders.

To obtain a good signal/noise ratio, i.e. an up-front distortion-free signal, keep the signal quite high, but make certain the red CLIP LED doesn't light up continually.

Find out the output level setting for your mixer (or other unit) and connect it to the input of the MAXIDRIVE3.4.

Adjust the MAXIDRIVE3.4 input gain if necessary:

Press the MODE key until the EDIT menu LED lights up.

Use the PREV and NEXT keys to go to the Input Gain page:

I n p u t

G a i n

Press ENTER.

The display will show the INA Gain or INA&B Gain page (according to the configuration and other utilities loaded in the memory):

7

Image 8
Contents MAXIDRIVE3.4 Safety Related Symbols Important Safety InstructionsPower Supply External ConnectionPreface Table of Contents Introduction Rear Panel Configuration of the system Getting StartedOutputs Inputs3 5 B 2 4 2 x 3 W Adjusting the input signal 3 B 2 4 S 5 2 x 2 W + 2 M aA d P r e s e t 2 x 3 W P u t I nFirst Setup System configuration 3 B 2 4 S 5 2 x 2 W + 2 M aA G a I N D B A & B G a I NNumber Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M a Type of Preset 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M a Menu MAP Configuration DescriptionPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D Store & Naming Preset O r e P r e s e t 2 x 2 W + 2 M aO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M aIncoming Dump Dump Out PresetT P r e s e t 2 W + 2 M a C o m i n g D u m p N o r e C e p t Delay Menu P u t D e l a y L a YM S T p u tInput Gain 2 u SEdit menu I N D BP u t Input EQGain Centre Frequency / Cutoff FrequencyBandwidth 0 0 H z V e rR u Phase F B e s 24 6 H z Crossover frequencyOutput EQ Output GainEditing values are between +6dB ~ -30dB, with 0.5dB steps Output PolV e r s e L a R I T YR m a Utility Menu Ganging SubmenuInput Ganging N g i n gP u t G a n g i n g T p u t G a n g i n g M . T h r e s h . U n i tM P e r a t u r e U n i t Units SubmenuT p u t M e t e r s E M u t e S t M u t e T u pP u t S e l e c t G i t a l A l o g M p e r a t u r e K e U p R m a l T eD C o n t r a s t Lock SubmenuTotal Partial C k2 2 W + 2 M a 3 B 2 4 S 5 A 1 3 B 2 4 S 5 2 2 W + 2 M a L O C KS s w o r d S s w o r d R DCOMM. Setup Submenu R m a t R dR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u pInputs a & B ConnectionsInputs a & B, Digital IN, RS485 Factory Preset Configuration Outputs 1 ~ 6, RS485 OUTRS232 Special attentions for RS232 interfaceSignal Power OrganizationA135 B246 3-WAY Stereo 2X2W Audio Mixer Signal PowerMAXIDRIVE3.4 Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Terms and Conditions Warranty Registration CardReturn Notice Seikaku Technical Group Limited