Nilfisk-ALTO 3.4 user manual P u t D e l a y, L a Y, M S, T p u t

Page 16

Output Delay only delays the signal of a specific output.

Also called Channel Delay, output delay is mainly used to compensate for the distance between different blocks of the same sound system (for example clusters) or to correct internal alignment of a speaker enclosure components.

5.2.1Input Delay

Use this menu page to adjust the delay lines of Input A, Input B and SUM.

I n p u t D e l a y

The values can be set in the following ranges:

I N A

D E L A Y

7 7 m S

IN A	ADC
IN A	ADC

INPUT DELAY

unit	range	step

m	0.0 ~ 900.0	0.5

mm	0 ~ 900000	7

ms	0 ~ 2621	1

us	0 ~ 2621438	21

The measurement unit can be chosen with the function Delay Unit (UTILITY menu - Units submenu).

5.2.2Output Delay

Use this menu page to adjust the delay lines of outputs 1, 2, 3, 4, 5, and 6.

O u t p u t

D e

l a y

Image 16

Contents MAXIDRIVE3.4 Safety Related Symbols Important Safety InstructionsPower Supply External ConnectionPreface Table of Contents Introduction Rear Panel Configuration of the system Getting StartedOutputs Inputs3 5 B 2 4 2 x 3 W Adjusting the input signal 3 B 2 4 S 5 2 x 2 W + 2 M aA d P r e s e t 2 x 3 W P u t I nFirst Setup System configuration 3 B 2 4 S 5 2 x 2 W + 2 M aA G a I N D B A & B G a I NNumber Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M a Type of Preset 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M a Menu MAP Configuration DescriptionPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D Store & Naming Preset O r e P r e s e t 2 x 2 W + 2 M aO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M aT P r e s e t 2 W + 2 M a Dump Out PresetIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu P u t D e l a y L a YM S T p u tEdit menu 2 u SInput Gain I N D BP u t Input EQBandwidth Centre Frequency / Cutoff FrequencyGain R u V e r0 0 H z Phase F B e s 24 6 H z Crossover frequencyOutput EQ Output GainEditing values are between +6dB ~ -30dB, with 0.5dB steps Output PolR m a L a R I T YV e r s e Utility Menu Ganging SubmenuP u t G a n g i n g N g i n gInput Ganging T p u t G a n g i n g M . T h r e s h . U n i tM P e r a t u r e U n i t Units SubmenuP u t S e l e c t G i t a l A l o g T u pT p u t M e t e r s E M u t e S t M u t e M p e r a t u r e K e U p R m a l T eD C o n t r a s t Lock Submenu2 2 W + 2 M a 3 B 2 4 S 5 C kTotal Partial A 1 3 B 2 4 S 5 2 2 W + 2 M a L O C KS s w o r d S s w o r d R DCOMM. Setup Submenu R m a t R dR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u pInputs a & B, Digital IN, RS485 ConnectionsInputs a & B Factory Preset Configuration Outputs 1 ~ 6, RS485 OUTRS232 Special attentions for RS232 interfaceSignal Power OrganizationMAXIDRIVE3.4 Audio Mixer Signal PowerA135 B246 3-WAY Stereo 2X2W Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Return Notice Warranty Registration CardTerms and Conditions Seikaku Technical Group Limited