Nilfisk-ALTO 3.4 A 1 3 B 2 4 S 5 2 2 W + 2 M a, L O C K, S s w o r d R D, M o r y R d

Page 30

T M A 1 3 B 2 4 S 5 6

2 U 2 2 W + 2 M A X

Note: alongside the symbol of Total or Partial protection, the letter M may also appear. This means that the system is protected, but the PRESET in question has undergone one or more changes that have not yet been stored. You can however switch the system on and off without any problems, as the current settings are kept in the buffer memory. Nevertheless, if this is your work setup, it's advisable to store it in a PRESET.

To unlock the protection:

Access the LOCK submenu.

The display shows the prompt for entering the password to unlock the protection.

The four alphanumeric characters of the password are encrypted.

U N L O C K

P a s s w o r d

[ * * * * ]

Enter in the password using the combination of the and keys and the DIAL, then press ENTER. Note: in the event of an incorrect password, the display prompts again, encrypting all the characters again.

U N L O C K

P a s s w o r d

[ B I R D ]

Protection is unlocked and the system enters default status.

5.4.5 MEMORY CARD SUBMENU

Memory Card

Format Card

Allows to format the Multimedia Memory Card.

Formatting is the preparation of the memory areas of the Card. Without formatting (or without compatible formatting) The Card can't be used by the system.

M e m o r y

C a r d

PREV NEXT ENTER

ESC

How to form at the Card

Insert a Multimedia Memory Card in the slot.

New or used Cards can be used, providing they are compatible (min 1MB).

29

Image 30

Contents MAXIDRIVE3.4 Power Supply Safety Related SymbolsImportant Safety Instructions External ConnectionPreface Table of Contents Introduction Rear Panel Outputs Configuration of the systemGetting Started InputsA d P r e s e t 2 x 3 W 3 5 B 2 4 2 x 3 W Adjusting the input signal3 B 2 4 S 5 2 x 2 W + 2 M a P u t I nA G a I N First SetupSystem configuration 3 B 2 4 S 5 2 x 2 W + 2 M a D B A & B G a I NName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M aType of Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Menu Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M aMenu MAP Configuration Description System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D O r e P r e s e t O p e r a H a l l Store & Naming PresetO r e P r e s e t 2 x 2 W + 2 M a E s e t N a m i n W + 2 M aDump Out Preset T P r e s e t 2 W + 2 M aIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu M S P u t D e l a yL a Y T p u t2 u S Edit menuInput Gain P u t I ND B Input EQCentre Frequency / Cutoff Frequency BandwidthGain V e r R u0 0 H z 4 6 H z PhaseF B e s 2 Crossover frequencyEditing values are between +6dB ~ -30dB, with 0.5dB steps Output EQOutput Gain Output PolL a R I T Y R m aV e r s e Utility Menu Ganging SubmenuN g i n g P u t G a n g i n gInput Ganging M P e r a t u r e U n i t T p u t G a n g i n gM . T h r e s h . U n i t Units SubmenuT u p P u t S e l e c t G i t a l A l o gT p u t M e t e r s E M u t e S t M u t e D C o n t r a s t M p e r a t u r eK e U p R m a l T e Lock SubmenuC k 2 2 W + 2 M a 3 B 2 4 S 5Total Partial S s w o r d A 1 3 B 2 4 S 5 2 2 W + 2 M aL O C K S s w o r d R DR m a t C a r d R m a t t i n g R m a t D o n e COMM. Setup SubmenuR m a t R d M m . S e t u pConnections Inputs a & B, Digital IN, RS485Inputs a & B RS232 Factory Preset ConfigurationOutputs 1 ~ 6, RS485 OUT Special attentions for RS232 interfaceSignal Power OrganizationAudio Mixer Signal Power MAXIDRIVE3.4A135 B246 3-WAY Stereo 2X2W Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Warranty Registration Card Return NoticeTerms and Conditions Seikaku Technical Group Limited